WE HAVE SOME GREAT LIMITED-TIME OFFERS - CLICK HERE TO VIEW THEM WE SHIP WORLDWIDE    /    All UK ORDERS GREATER THAN £75 EX VAT DELIVERED FREE    /    WE SHIP WORLDWIDE    /    ALL EUROPEAN ORDERS GREATER THAN £500.00 ex VAT DELIVERED FREE    /    WE SHIP WORLDWIDE

BRB 2 Tool Bits

BRB 2 Tool Bits FAQs

Answers on choosing, fitting and looking after the multifunction cutting tool bits used on a small tube bevelling machine.

Why does the tube end need to be faced as well as bevelled?icon-minus-redicon-plus-red

Facing makes the end square to the tube axis and leaves it clean and free of burrs and saw marks, which gives a consistent land and fit-up. Trade guidance on orbital welding says tube ends must be square, clean and well matched, and that a gap, burr or dirt at the joint can cause a faulty weld that no change in welding settings will correct.

Bevelling then adds the angle needed for the joint. Doing both from the same set-up helps keep the bevel concentric with the bore, so the two ends line up properly when joined.

What bevel angle and land should the bit produce?icon-minus-redicon-plus-red

The angle, land (root face) and gap depend on the joint design, material, thickness and welding process, and should be taken from your welding procedure or the relevant code. The bevel gives access to the whole joint, and smaller angles and gaps increase the risk of defects.

Choose a bit that produces the form your procedure calls for, and measure the first prepared end before working through a batch.

How should I change a tool bit safely?icon-minus-redicon-plus-red

Make the machine safe before you start. The HSE says to ensure moving parts have stopped and to isolate electrical and other power supplies, and to lock off the machine if there is any chance the power could be switched back on. For an air-driven machine, disconnect the air line as well.

Then follow the maker's instructions for removing and fitting the bit, using the correct tools and fixing screws. The HSE advises using the manufacturer's maintenance instructions as a guide, particularly for safety-critical features. Clean the seat before fitting, tighten fixings as specified, and turn the head by hand to check it moves freely before restarting.

Do I need cutting fluid, and is it a health risk?icon-minus-redicon-plus-red

Whether cutting fluid or lubricant is used depends on the maker's instructions and the material. If it is, treat skin contact seriously. The HSE lists skin irritation and dermatitis as main health effects of metalworking fluids, and says skin exposure should be prevented where reasonably practicable or, failing that, adequately controlled.

Use only the recommended fluid and keep unprotected hands, forearms and face away from it. Where contact cannot be avoided, the HSE advises suitable gloves, mild skin cleaner and washing facilities, drying the skin well, moisturising after work, and checking your hands regularly for itchy, dry or red skin. Check the product's safety data sheet.

What protective equipment should I use when machining?icon-minus-redicon-plus-red

Choose eye protection that suits the hazard. The HSE says it should give the right combination of protection against impact, dust, splash or molten metal for the task, and fit the user properly. Swarf and fragments can fly or bounce back, so your risk assessment should decide the type.

The HSE also says PPE should be assessed as fit for purpose, maintained and stored properly, and backed by instruction and training. Near rotating tools, avoid gloves, loose or baggy clothing and jewellery including rings, and tie back long hair, because rotating parts can catch them. Handle used bits and swarf only when the machine has fully stopped, because edges stay sharp.

How do I know when a tool bit is worn?icon-minus-redicon-plus-red

Trade guidance on cutting tools lists the common warning signs: a poorer surface finish, higher cutting force or load, squealing or vibration, tube ends drifting out of size, visible wear or chipped edges, and a bit that wears out faster than usual.

Replacing too late can scrap a tube end or break the cutter, while replacing too early wastes useful life. Look at the cutting edge under good light each time you change tube size or material.