WE HAVE SOME GREAT LIMITED-TIME OFFERS - CLICK HERE TO VIEW THEM WE SHIP WORLDWIDE    /    All UK ORDERS GREATER THAN £75 EX VAT DELIVERED FREE    /    WE SHIP WORLDWIDE    /    ALL EUROPEAN ORDERS GREATER THAN £500.00 ex VAT DELIVERED FREE    /    WE SHIP WORLDWIDE

CK20 Torch Parts

CK20 Torch Parts FAQs

Torch bodies, handles, back caps and cable and hose sets for a water-cooled TIG torch: how to pick the right part and look after it.

What is in a water-cooled torch assembly and which parts wear?icon-minus-redicon-plus-red

A water-cooled TIG torch is built from a torch body (the head), a handle, a back cap and a cable and hose set that carries welding current, shielding gas and coolant to and from the machine. The international standard for arc welding torches treats the torch as the body, the cable-hose assembly and other components together, so the rating plate and manual matter.

The parts that usually wear first are the back cap and its O-ring, the hoses and power cable, and the connections at the machine end. The body and handle tend to last longer but can be damaged by heat, drops or coolant leaks. Check the manual for the exact parts list.

When is a water-cooled torch a better choice than an air-cooled one?icon-minus-redicon-plus-red

Air-cooled torches can overheat during long welding runs, and the usual answer is either to let them cool or to move to a water-cooled torch. Water-cooled torches are therefore generally chosen for sustained higher-current work and long arc-on times.

Air-cooled torches are lighter and simpler because they need no cooler. A water-cooled torch needs a suitable cooler connected to the machine and the hoses kept in good order. The current at which people switch varies between makers and sources, so look at the rated current and duty cycle in your torch manual rather than relying on a rule of thumb.

How do I know coolant is actually flowing through the torch?icon-minus-redicon-plus-red

Do not judge flow by feel. Some makers' manuals say to make sure the coolant is circulating correctly while you weld, and with their own coolers this can be seen as a steady return flow in the cooler's tank. Many coolers also have a flow switch or warning light, so check what yours has.

If the return flow stops, the handle gets hot or the cooler alarms, stop welding and find the cause: a low level, a kinked hose, a blocked line or a cooler fault. Running the torch without flow can quickly damage the power cable and the head, so check flow every time you start work.

What coolant should I use and what should I avoid?icon-minus-redicon-plus-red

Use the coolant recommended by the makers of your torch and cooler. A water-cooled torch must never be put into service without coolant, so check the level before every session.

Plain tap water is generally advised against: it conducts electricity, so current passing through the circuit can cause corrosion that releases particles and blocks the narrow passages, scale can build up, and it can freeze in cold conditions. Ordinary car antifreeze should only be used if the manuals say it is suitable, because additives vary. A purpose-made, low-conductivity welding coolant is the usual choice. Do not mix liquids unless the manual says you can, and follow the cooler manual for how often to test or change the coolant.

When should I replace a power cable, hose or the whole cable set?icon-minus-redicon-plus-red

Look over the cable set before each shift. Insulation on cables and the torch should be undamaged, and defects should be reported rather than worked around. Replace the set if you find cuts, abrasion, kinks, hardened or discoloured sections, bulging or bubbling hose, or weeping at the fittings.

A damaged power cable or hose can leak coolant, overheat and, in a worst case, expose live parts, so do not carry on with it or try a temporary repair. Isolate the machine from the mains and switch off the cooler before you disconnect anything, and make sure the replacement is made for the same torch type and cooling method.

What should I do when I disconnect the hoses from the cooler?icon-minus-redicon-plus-red

Switch off and isolate the machine and the cooler first, and let the torch and coolant cool down, as some coolant stays in the torch body and can be hot after welding.

Some torch manuals tell you to seal the coolant hoses with the plastic stoppers supplied whenever they are detached, which stops coolant escaping onto the floor or electrical parts. Keep coolant away from the machine and from live connections, and wipe up spills at once. When you reconnect, match the connectors by their markings or colours, tighten them correctly and check for weeping before you start welding.