WE HAVE SOME GREAT LIMITED-TIME OFFERS - CLICK HERE TO VIEW THEM WE SHIP WORLDWIDE    /    All UK ORDERS GREATER THAN £75 EX VAT DELIVERED FREE    /    WE SHIP WORLDWIDE    /    ALL EUROPEAN ORDERS GREATER THAN £500.00 ex VAT DELIVERED FREE    /    WE SHIP WORLDWIDE

CK TL210 Gas Saver Spares

CK17 Gas Saver Spares FAQs

Answers to common questions about choosing, fitting and looking after gas saver (gas lens style) spares for this type of TIG torch.

What is a gas saver set and how is it different from a standard collet body and cup?icon-minus-redicon-plus-red

A gas saver set replaces the standard collet body with a gas-lens style part that contains a fine mesh screen, and it is usually paired with a larger cup. A gas lens usually gives a smoother, more laminar gas flow, which improves shielding on corner, edge and curved joints. The tungsten is still held by an ordinary collet.

Designs differ between torch types, so check your torch manual to see which parts your torch uses and whether a different heat shield or insulator is needed.

How do I work out which gas saver parts fit my torch?icon-minus-redicon-plus-red

Start with the torch type or series, usually shown on the torch head or handle and in the manual. Parts are normally grouped by series, but gas saver parts also come in different body lengths (standard, short, large diameter) and may need a matching insulator or heat shield.

Note the tungsten diameter you use, then compare the old part with the new one and with the manual's parts list. Do not assume a part from another series fits just because it threads in. If you are unsure, our team can help you check before you order.

Why must the collet and collet body match the tungsten diameter?icon-minus-redicon-plus-red

The collet grips the tungsten inside the collet body when the back cap is tightened. If either part is the wrong size, the tungsten can sit loose, make poor electrical contact, overheat and give an unstable arc.

Replace a collet that is distorted, burnt or no longer grips the tungsten firmly when the back cap is tightened. Match the collet body and collet to the tungsten diameter you weld with, and check the manual for the sizes your torch accepts.

When would I choose a large diameter gas saver set rather than a standard one?icon-minus-redicon-plus-red

A large diameter set gives a wider blanket of shielding gas, which helps on materials that need more protection from the air, such as stainless steel and titanium. Titanium needs extra gas protection, so a gas lens and a large cup are often used.

The trade-off is a bulkier torch head that can be harder to fit into tight corners and can restrict your view of the joint. For awkward access a short set may suit better, so choose by the electrode diameter and how accessible the joint is. Always use a cup and body made for your torch type.

Why is a high gas flow a problem, even with a gas saver set?icon-minus-redicon-plus-red

More gas is not better. Too high a flow makes the gas column turbulent, which can draw air into the shield and cause porosity, discolouration and an unsteady arc. A gas lens gives smoother flow than a plain collet body, but it does not remove the limit.

Use the lowest flow that gives good coverage for your cup size, joint and material, following the torch maker's guidance and your welding procedure. If you get porosity, check for leaks and damaged parts before simply turning the gas up.

How far can the tungsten stick out with a gas saver set?icon-minus-redicon-plus-red

A gas lens style body usually allows a longer tungsten stick-out than a standard collet body, which helps with visibility and reaching into joints. It is not unlimited: the safe distance depends on cup size, gas flow, material and the joint.

A longer stick-out leaves more tungsten exposed, so keep it as short as the joint allows, and consider gas pre-flow and post-flow to protect the tungsten at start and finish. Follow your welding procedure and the torch maker's instructions for the stick-out suited to your cup.

TL210 Gas Saver Spares