WE HAVE SOME GREAT LIMITED-TIME OFFERS - CLICK HERE TO VIEW THEM WE SHIP WORLDWIDE    /    All UK ORDERS GREATER THAN £75 EX VAT DELIVERED FREE    /    WE SHIP WORLDWIDE    /    ALL EUROPEAN ORDERS GREATER THAN £500.00 ex VAT DELIVERED FREE    /    WE SHIP WORLDWIDE

Double Seal Purge System

  • DSK16-X Silicon Double Seal Purging Complete Kit

    Silicon Double Seal Purging Complete Kit

    Rapid ref : DSK16-X
     
    Shop Parts

    From £ 1700.00 EX VAT
     

       Expand Options

  • DSFXX Double Seal Gas Finger, for 16 - 38mm Pipe I.D.

    Double Seal Gas Finger, for 16 - 38mm Pipe I.D.

    Rapid ref : DSFXX
     
     

    From £ 32.98 EX VAT
     

       Expand Options

  • DSXX-X Double Seal Purging System, for 16 - 320mm Pipe I.D.

    Double Seal Purging System, for 16 - 320mm Pipe I.D.

    Rapid ref : DSXX-X
     
    Shop Parts

    From £ 48.94 EX VAT
     

       Expand Options

Double Seal Purge System FAQs

Answers on setting up, sizing, venting and safely using a twin-disc purge system inside pipe and tube.

How is a double seal purge system set up around the joint?icon-minus-redicon-plus-red

A double seal system places a sealing disc on each side of the joint, joined by a flexible or rigid tube. Purge gas is fed into the sealed section between them, pushing out the air, and the displaced air and spare gas leave through a vent.

The idea is the same as any purge dam: seal off a short length of pipe and fill only that section with inert gas, so the back of the weld is protected from oxygen. Exact disc spacing, hose routing and gas connections vary between designs, so follow the maker's instructions for your kit.

Why does a double seal system use less gas than flooding the whole pipe?icon-minus-redicon-plus-red

Because only the short length between the two seals is purged, not the whole bore. The HSE notes that the quantity of gas released can be significantly less with localised purging techniques such as damming than when an entire pipe or vessel is flooded.

A smaller purged volume generally means a faster purge and less gas to vent afterwards. It also means less gas to be released if something goes wrong, which is a safety benefit as well as a practical one.

Can I rely on the seals to stop purge gas escaping into the pipe?icon-minus-redicon-plus-red

No. The HSE states that the seal on dams and bladders should not be relied on to prevent gas leakage, and that the pipe or fabrication may still become a confined space. Gas can pass the discs, especially if the fit is poor or the bore is irregular.

That means you must plan for it: vent spare gas safely, never put your head or body into pipework that has held inert gas, and carry out a risk assessment before the work starts. If entry into a space that may contain purge gas cannot be avoided, a safe system of work and a calibrated oxygen meter are essential.

Where should the vent from a double seal purge go?icon-minus-redicon-plus-red

Excess purge gas should be led away, ideally outside the pipe or fabrication, rather than released into a confined or poorly ventilated area. The HSE describes bleeding excess gas from dams through hoses and discharging it outside the fabrication.

In a workshop, make sure the vent outlet is in a well-ventilated place away from low-lying areas such as pits and sumps where argon in particular can collect. Keep the vent clear and unrestricted during welding, and check your risk assessment covers where the gas will end up.

Does a short purge time mean I can skip checking the oxygen level?icon-minus-redicon-plus-red

No. Makers often quote short purge times, but the actual time depends on pipe size, gas flow and how well the discs seal on your job. Time alone does not prove the oxygen has dropped far enough.

The most reliable way to know is to measure the oxygen at the vent or in the purged section with a suitably calibrated oxygen meter and weld only when it reads at or below the level your welding procedure requires. Trade guidance also stresses that allowing plenty of time does not guarantee the oxygen has been removed, and that a device capable of accurate and reliable measurement is the best option.

Why should I introduce the purge gas slowly?icon-minus-redicon-plus-red

A gentle flow lets the gas push the air out ahead of it instead of churning the two together. Trade guidance on weld purging advises that the inert gas should enter slowly, with the vent at the opposite end or highest point so air can escape as it is displaced.

A flow that is too high tends to cause turbulence, which can mix air back into the purge gas and slow down reaching a low oxygen reading. Start low, let the oxygen reading fall, and do not set a flow that blows the discs out of position or pressurises the section. The right flow depends on the pipe size and the maker's guidance.