WE HAVE SOME GREAT LIMITED-TIME OFFERS - CLICK HERE TO VIEW THEM WE SHIP WORLDWIDE    /    All UK ORDERS GREATER THAN £75 EX VAT DELIVERED FREE    /    WE SHIP WORLDWIDE    /    ALL EUROPEAN ORDERS GREATER THAN £500.00 ex VAT DELIVERED FREE    /    WE SHIP WORLDWIDE

MRA Accessories

  • 790008018 Multi-roller Cutting Chain for MRA, Tube OD 33.7-114.3mm, 15 Cutting Pieces

    Multi-roller Cutting Chain for MRA, Tube OD 33.7-114.3mm, 15 Cutting Pieces

    Rapid ref : 790008018
    Mfr Ref : 790008018
     


    £ 258.00 EX VAT
     

  • 790008041 Multi-roller Cutting Chain for MRA, Tube OD 114.3-254mm, 16 Cutting Pieces

    Multi-roller Cutting Chain for MRA, Tube OD 114.3-254mm, 16 Cutting Pieces

    Rapid ref : 790008041
    Mfr Ref : 790008041
     


    £ 389.00 EX VAT
     

  • 790008XXX Orbitalum MRA Clamping Shells, 25 - 254mm

    Orbitalum MRA Clamping Shells, 25 - 254mm

    Rapid ref : 790008XXX
     
     

    From £ 231.00 EX VAT
     

       Expand Options

MRA Accessories FAQs

Straight answers to the questions buyers ask about cutting chains and clamping shells for a chain-type metal tube cutter.

What is a multi-roller cutting chain and how does it cut a tube?icon-minus-redicon-plus-red

It is a chain of small hardened cutting wheels that is wrapped around the tube and tensioned by the cutter's lever. As you lever, the wheels press into the wall and work their way round until the tube is cut through. The cut is chipless and the tool needs no electric power.

The chain runs round the tube at right angles, and diameter-specific clamping shells hold the cutter in line, which is what gives a straight cut. The wheels do the work, so the chain is the part that wears, and the maker allows for replacing individual wheels or the whole chain.

How do I choose the right cutting chain?icon-minus-redicon-plus-red

Match the chain to the outside diameter of your tube. Chains are made for a band of diameters, with one covering smaller tubes and another covering larger ones, and the number of cutting wheels differs between them. Check the diameter range stated for the chain and make sure your tube falls inside it.

Also check the wall thickness and the material. These cutters are designed for thin-walled tube, and the maximum thickness is lower for high-alloy steels such as stainless than for plain steel. Look up the limits in the cutter's manual rather than guessing.

How do I fit the clamping shells so the cut comes out square?icon-minus-redicon-plus-red

Fit the shells at the cutting point so they sit tight against each other, parallel, and locked firmly onto the tube with their screws. They guide the cutter, so any looseness or tilt shows up as a crooked cut.

The maker recommends turning one shell a quarter turn relative to the other, so the gaps between the halves are offset, to make the pair more stable. If the tube is not fixed in place, hold it in a clamp or vice, otherwise the shells can open up as the tube is cut through on one side.

Why is the chain running unevenly, or the cut off square?icon-minus-redicon-plus-red

Uneven running usually points to damaged cutting wheels. The maker says this can be caused by uneven levering, and in particular by rocking the lever left and right while tensioning the chain. Tension the chain only during a steady levering stroke, then return and re-tension on the next one.

If wheels are damaged, replace the individual wheels or the whole chain. A cut that is off square can also come from shells that are loose, not parallel or not matched to the tube size, so check those first.

Why does a square, burr-free tube end matter before orbital welding?icon-minus-redicon-plus-red

Orbital welding heads expect two clean, flat ends that meet without gaps. Tube-cutting and fitting makers state that the end needs to be square, free of burrs and clean, and that missing any of these can lead to a poor or rejected weld.

A chain cutter gives a right-angled end without deformation, which the maker says needs little further preparation for many connection methods. Even so, inspect every end, and deburr or face it if your welding procedure or the weld head maker requires it. Follow your own procedure for the acceptance limits.

What safety precautions apply when using a chain tube cutter?icon-minus-redicon-plus-red

The chain is sharp, so wear safety gloves when handling, carrying or using the cutter, and do not touch or grip the chain while it is in use. Check the cutter for visible damage before each day's use and have any defect repaired straight away.

Only use the tube sizes and materials listed in the manual, and use the maker's own spare parts. Dispose of used cutting oil and tube waste according to the rules that apply to your workplace, and choose gloves and other protection using your own risk assessment.