WE HAVE SOME GREAT LIMITED-TIME OFFERS - CLICK HERE TO VIEW THEM WE SHIP WORLDWIDE    /    All UK ORDERS GREATER THAN £75 EX VAT DELIVERED FREE    /    WE SHIP WORLDWIDE    /    ALL EUROPEAN ORDERS GREATER THAN £500.00 ex VAT DELIVERED FREE    /    WE SHIP WORLDWIDE

REB Pipe Bevelling Machines

The most powerful pipe end preparation solution

  • Compact design for precise and reproducible weld prep profiles
  • Quick tool change QTC®
  • Square and burr free
  • High performance coated tool bit with two or four cutting edges
  • Optimised performance and ergonomic drive system
  • Portable with an integral handle

 

Machine comes with

  • 1 Pipe end preparation machine
  • 1 Transportation case
  • 2 clamping chucks
  • 6 clamping sets
  • 1 Tool set
  • 1 KSS TOP lubricant spray pump
  • 1 Set of operating instructions

 

REB Pipe Bevelling Machines FAQs

Answers to common questions about inside-clamped pipe end preparation machines with a pneumatic drive, used to bevel and face pipe ends before welding.

What does a pipe end preparation machine do?icon-minus-redicon-plus-red

It prepares the end of a pipe for welding by cutting a bevel and facing the end square, using a rotating tool head. The machine is clamped inside the bore of the pipe, so the cut runs true to the pipe and each end can be prepared the same way.

For larger pipe a multi-edged cutting tool can usually be used for different operations, such as facing and bevelling, and on different wall thicknesses and materials. Check the maker's instructions for the pipe sizes, wall thicknesses and materials your machine is approved for, because these limits are specific to each machine and are on the data plate and in the manual.

How do I choose the right clamping wedges and chuck?icon-minus-redicon-plus-red

These machines grip the inside of the pipe, so the clamping parts are chosen by the pipe's inside diameter, not its outside size. Work out the bore first (outside diameter less twice the wall thickness), then pick the wedge set and clamping chuck whose range covers it. Ranges overlap in steps, so choose the set where your bore sits comfortably within the range rather than at the very edge.

The maker's manual has a table matching bore ranges to wedges and chucks. After clamping, centre the mandrel in the pipe and check it is firm before you start, and keep the wedges and their seats clean so they grip evenly.

Does the pipe need to be cut square before I use the machine?icon-minus-redicon-plus-red

It helps a great deal. The machine faces and bevels, but it is not meant to fix a badly angled saw cut. The maker warns that a pipe which is not sawn off square can damage the tool if the cutting edge starts too close to the pipe end, so before switching on, check there is enough clearance between the edge and the pipe end.

Feed the tool in slowly until it first touches, then keep an even pressure once the edge is cutting all the way round. Rushing the first contact is a common cause of a chipped edge and a rough start to the cut.

Do I need cutting lubricant, and which one should I use?icon-minus-redicon-plus-red

Yes. Machining with lubrication generally extends the life of the cutting tools and allows a larger feed rate. Use the type of cutting lubricant the machine maker recommends in the manual rather than a general oil.

Apply it at the cutting area during the cut, and be careful with chip removal afterwards. Lack of lubrication is one of the causes the maker lists for poor surface quality on cut and bevelled faces, so if your finish looks rough or the tool is wearing quickly, check lubrication before anything else.

What are the main safety points when using a pipe end preparation machine?icon-minus-redicon-plus-red

Chips can be hot and sharp, and the cutting edges are sharp, so wear safety goggles and keep hands away from the tools while the machine runs. Do not wear gloves near the rotating tool head, because they can be caught; wear safety gloves for handling tools and removing chips once the machine has stopped. Tie back long hair and avoid loose clothing, jewellery or ties that could be caught by the rotating parts.

Switch the machine off after each stage and let it stop. Before changing tools, cleaning or maintenance, isolate the air supply and let the machine run down. Long, heavy pipe must be supported at the free end so the machine does not overturn. Follow the maker's instructions and your own risk assessment.

What compressed air supply does a pneumatic drive need?icon-minus-redicon-plus-red

A pneumatic machine needs an air supply that can supply enough flow at the working pressure, and the figures are on the data plate and in the manual. Low pressure or a network shared with other tools is a typical reason for a machine that runs slowly or lacks power; the maker's fault guide suggests disconnecting other users and restoring the specified pressure.

The maker also calls for a maintenance unit (water collector, pressure reducer and lubricator) fitted upstream, with only a short air line between that unit and the machine. Clean, dry, correctly lubricated air protects the air motor and is the simplest way to avoid stalling and wear.