WE HAVE SOME GREAT LIMITED-TIME OFFERS - CLICK HERE TO VIEW THEM WE SHIP WORLDWIDE    /    All UK ORDERS GREATER THAN £75 EX VAT DELIVERED FREE    /    WE SHIP WORLDWIDE    /    ALL EUROPEAN ORDERS GREATER THAN £500.00 ex VAT DELIVERED FREE    /    WE SHIP WORLDWIDE

Pipe Stands

Pro Jack, Fold-A-Jack, Heavy Duty Jack Accessories.

Pipe Stands FAQs

Practical answers on choosing, setting up and looking after adjustable pipe stands and their heads.

How do I read the load rating on a pipe stand?icon-minus-redicon-plus-red

The rating in the maker's manual or on the stand is normally the maximum load for one stand, not for a set. Split the weight of the pipe between the stands and keep each one within its own limit. If a pipe is heavy, add another stand rather than overloading one.

Fitting accessories such as different heads can lower the maximum capacity, and accessory heads can carry a lower rating than the stand itself, so check the rating of every head and attachment as well as the base. If you cannot find the rating or are unsure, do not use the stand until you have checked the maker's instructions.

Can I adjust the height or move a pipe stand with the pipe on it?icon-minus-redicon-plus-red

No. Makers of pipe jack stands say never to change the height of a stand, or move it, while it is under load. Remove the load first, then adjust or move the stand.

Set the height before the load goes on, keep every stand supporting one pipe at the same height, and lower the pipe on gently rather than dropping it onto the stand. Keep hands and other body parts out from between the pipe and the stand head.

Lock the head assembly before moving a stand, and do not wind a stand beyond the maker's height limit marking, as an over-extended stand is unstable.

Does it matter what the floor is like under a pipe stand?icon-minus-redicon-plus-red

Yes. Makers say to use stands only on solid, level surfaces that will support the weight of the load, not on inclines, and to avoid dirt or gravel. All the feet of each stand should make solid contact with the floor.

If the floor is uneven or soft, move the work to a better spot or use a firm, flat base under the feet rather than packing the legs with makeshift material. Check that the feet are all in solid contact before you load the pipe, and keep the stand out of walkways.

What damage means a pipe stand should be taken out of use?icon-minus-redicon-plus-red

Check a stand for damage before each use. Makers list signs such as legs or base that are bent, twisted or showing fatigue, cracked or rusted welds, a bent lock ring (which points to overload), a cracked, bent or worn head, a head that tilts or rotates under load, and a pipe that cannot be centred in the V-head.

Any of these can let the pipe slip, roll or fall, or the stand tip. Take a damaged stand out of use. If the maker does not supply the part as a replacement, do not try to repair it.

Under the Provision and Use of Work Equipment Regulations, the HSE says work equipment must be maintained in an efficient state, working order and good repair and inspected so faults are caught early.

Can I put more than one pipe on a stand?icon-minus-redicon-plus-red

No. Makers say never to place more than one pipe on pipe jack stands. Two pipes or an off-centre load can unbalance the stand and exceed the rated load on the head.

Support each pipe on its own set of stands. Use at least two stands, set to the same height and fitted with the same head style, so the load is shared evenly and will not tip or move. Centre the pipe on the heads and consider its length, diameter and weight when deciding how many stands you need.

If you are unsure, add stands rather than stacking pipes.

What should I do if the pipe on a stand starts to slip or tip?icon-minus-redicon-plus-red

Do not reach out to steady or catch it. Makers say that if a load becomes unstable you should move away from the work area quickly, because a falling pipe can cause serious injury.

Never allow anyone to stand beneath a supported pipe, and keep hands clear of the gap between the pipe and the stand head when positioning it.

After an incident, remove the load, check the stand for bent legs, a bent lock ring or a damaged head before it is used again, and think about whether the pipe needs another stand, a hold-down device or a better base. Review the set-up with your risk assessment.