WE HAVE SOME GREAT LIMITED-TIME OFFERS - CLICK HERE TO VIEW THEM WE SHIP WORLDWIDE    /    All UK ORDERS GREATER THAN £75 EX VAT DELIVERED FREE    /    WE SHIP WORLDWIDE    /    ALL EUROPEAN ORDERS GREATER THAN £500.00 ex VAT DELIVERED FREE    /    WE SHIP WORLDWIDE

RPG 8.6 Accessories

RPG 8.6 Accessories FAQs

Questions about tool holders, clamping shells and other accessories for orbital tube squaring and bevelling machines.

What does a tool holder do on a tube squaring and bevelling machine?icon-minus-redicon-plus-red

The tool holder carries the cutting tool and sets the shape that is machined on the tube end. Different holders are made for different jobs, such as squaring the end flat, or cutting a bevel at a set angle ready for a butt weld. Changing the holder lets one machine prepare ends in more than one way.

Holders are normally made for a particular machine type and size range, so check the data plate and manual for the holders the machine is designed to accept rather than assuming one will fit.

How do I choose the right bevel angle holder?icon-minus-redicon-plus-red

Start with the weld procedure or drawing, because that sets the bevel angle, the root face (land) and the gap. Holders are commonly made for angles such as 30, 37.5 and 45 degrees. A 37.5 degree bevel on each end is widely used for pipe butt welds, giving about 75 degrees included between two prepared ends.

Check how the angle is measured. The 37.5 degrees is normally taken from a line square to the tube axis (the plane of a square-cut end), not from the axis itself, but makers and drawings do not always use the same convention. If the procedure is unclear, ask the welding supervisor before machining.

Why do tube ends need squaring before welding?icon-minus-redicon-plus-red

A flat, square end lets the two tubes sit tightly together and stay aligned, and the weld quality depends directly on the quality of the preparation. This matters most for automatic orbital welding, where the weld head cannot make up for a poor fit.

Squaring is often worth doing even when a saw cut looks straight, because it can remove small burrs and the scratches a saw can leave. A clean, burr-free face also helps keep the inside of the tube clean, which matters for high-purity work. Follow your weld procedure and any cleanliness specification for the preparation required.

What are clamping shells and why are they used?icon-minus-redicon-plus-red

Clamping shells are split inserts that fit around the tube and hold it in the machine. Because they match the tube's outside diameter, they spread the clamping force around the tube instead of pinching it at a few points.

That is particularly useful for thin-wall tube, where ordinary jaws can distort the tube. Makers describe shells of this kind as giving deformation-free clamping. A tube that has been squeezed out of round is harder to cut square and harder to fit up for welding.

How do I select the right clamping shells for my tube?icon-minus-redicon-plus-red

Shells are matched to the tube outside diameter, and for thin-wall tube the wall thickness may also matter, so have the exact outside diameter and wall thickness to hand. Makers normally ask for these when shells are specified.

Each set covers a limited diameter range, and the machine itself has a minimum and maximum tube size, so a set that suits one tube will not necessarily suit the next size. Fit only the shells the manual lists for your machine, and check the tube is gripped firmly but is not marked or distorted.

Can I use the same machine and accessories on stainless steel and carbon steel?icon-minus-redicon-plus-red

It is best not to, unless the accessories are kept clean and separate. Carbon steel particles picked up from tools or clamping surfaces can embed in stainless steel and later rust, which damages its corrosion resistance. Bevelling and tube machining guidance recommends keeping tools and parts for stainless steel only for that material and storing them apart.

If a shared machine is unavoidable, clean the contact surfaces and fit stainless-only shells and tools, and follow any contamination requirements in your welding specification.