Tube squaring machines face the ends of thin-walled tube so they are square, burr-free and ready for welding.
What kind of tube is a tube squaring machine designed for?

These machines are designed for thin-walled tube, mainly stainless steel and other steels, and for small welded fittings, where a clean, square end is needed before orbital welding. The maker states a maximum wall thickness and a range of tube outside diameters for each model, and the clamping shells have to match the diameter you are working on.
The tool bit is also limited. Makers list the materials their machines are suited to, which typically include alloy and unalloyed steels and some softer metals such as aluminium, and ask you to check with them for anything else. Do not assume a thick-walled pipe can be faced.
Read the data plate and the manual for the limits of your machine, and choose the model that covers your largest tube.
How does a tube squaring machine work?

The tube is clamped by its outside diameter in a pair of clamping shells so that it is held centrally. A motor-driven tool holder with a cutting tool then rotates against the end of the tube and machines the end face flat. The cut is brought in with a feed that has graduations on it, so you can advance the tool in very small, controlled steps.
Quick-change fittings on most models let you swap shells and tools without separate tooling. Because the tube is held and faced in a single set-up, the result is an end at right angles to the tube axis with little or no burr.
The feed system, speed settings and tool differ between models, so follow the maker's instructions for yours.
Why square a tube end if the saw cut already looks straight?

A saw or abrasive cut can look straight and still leave a slightly angled face, burrs or scratches. Makers of orbital welding equipment say that high-quality end preparation is required for automatic welding, and that pipe ends should be square, free of burrs and free from contamination, because even small deviations in the joint can lead to weld defects or rework.
A squaring machine faces the end square to the tube axis in one set-up. Whether you need it depends on your saw cut and on the standard set by your welding procedure or specification, so check those first.
What safety precautions should I take when using a tube squaring machine?

The tool spins at the end of the tube, so keep your hands away from it while it runs, tie back long hair and do not wear loose clothing, jewellery or a tie. Wear eye protection against hot, sharp chips. Use the machine only with the tube properly clamped and with the chip shield or viewing window closed, where one is fitted.
Switch off and let the machine stop completely before you change the tool, change the shells, clean it or remove chips. Pull out the plug or take out the battery first. Safety gloves are for handling sharp chips and cut ends once everything has stopped, and the HSE warns that gloves near rotating machinery raise the risk of entanglement, so keep hands clear of anything that is turning.
Always follow the maker's manual and your own risk assessment.
How do I use a mains-powered squaring machine safely?

Before each use, inspect the machine, cable and plug for damage. The HSE advises checking that the cable is not damaged and has not been repaired with tape or an unsuitable connector, and looking for burn marks or discolouration. If anything is damaged, do not use it, and have a competent person repair it.
Run the machine from a supply protected by a residual current device (RCD). The HSE describes an RCD as a useful safeguard but only a secondary one, and says the user should test it with its test button before use. Keep the cable clear of the cutting area and away from sharp chips, oil and heat, never carry the machine by the cable, and do not leave it running unattended.
Check that the supply matches the data plate.
Should I choose a mains or a cordless machine?

Think about where you will use it. A mains-powered machine gives steady power for repeated work in a workshop. A cordless machine suits fitting and site work where there is no convenient socket, but it relies on charged batteries, so plan for a spare charged battery on a bigger job.
Before using the battery and charger, read the maker's instructions for them completely. Take the battery out before changing tools or cleaning. If the battery runs low the cut can suffer, so charge or swap it.
Also check that the model covers your largest tube diameter and wall thickness, because the range differs between models.