WE HAVE SOME GREAT LIMITED-TIME OFFERS - CLICK HERE TO VIEW THEM WE SHIP WORLDWIDE    /    All UK ORDERS GREATER THAN £75 EX VAT DELIVERED FREE    /    WE SHIP WORLDWIDE    /    ALL EUROPEAN ORDERS GREATER THAN £500.00 ex VAT DELIVERED FREE    /    WE SHIP WORLDWIDE
    Share this page on Facebook   Share this page on LinkedIn   Share this page on Twitter   Share this page on Whatsapp   

    Rapid Ref : 209010-SET3  

    HMT VersaDrive Cobalt Drill Bit InsertFoam 7 Piece Set (5, 6, 6.8, 8, 8.5, 10, 10.2mm)
    209010-SET3

    Click here to see what's included

    £173.87  EX VAT
    SSP Suggested Selling Price = £204.55  YOU SAVE £30.68
     Buy in 3 easy interest free payments of £57.96† with

    SIMPLY THE BEST LONG-LIFE TWIST DRILL BITS FOR METAL.

    All VersaDrive Drill Bits can be used in any standard 1/2" drill chuck for cordless or pistol drill use or adapted for use in a Magnet Drill or Impact Wrench.

    Fast drilling with minimal kickback; dual hardened for impact wrench use up to 10mm. Precision Ground Flutes with deep web design for easy chip clearance. 135 Split Point for easy starting and high accuracy 8% Cobalt for long life and endurance in structural steel and hard metals. GoldMax Low Friction Titanium Coating to Stop Heat Burnout. High Strength, Non-Slip Shank Design.

    Product Details

    Brochures & Manuals

    BROCHURES & MANUALS
       View Brochure

    HMT Drill Bits FAQs

    Answers to common questions about choosing and using cobalt, impact and general purpose drill bits for steel.

    How should I drill stainless steel without ruining the bit?icon-minus-redicon-plus-red

    Stainless steel work hardens when it gets hot or when the bit rubs instead of cutting. Use a sharp bit, a moderate speed, and a firm, steady feed so the bit keeps cutting. Do not let it dwell or rub in the hole.

    Use cutting fluid and watch the swarf: good chips are clean spirals, and dark or powdery chips mean too much heat. Narrow bits need a minimum speed, while larger bits and deep holes should run slower. Check the bit maker's speed chart for your grade of stainless, and clamp the work firmly.

    What loose clothing, hair or glove precautions apply when drilling?icon-minus-redicon-plus-red

    Drills are rotating machinery, and entanglement is a serious risk. The HSE advises avoiding loose or baggy clothing, tying back or covering long hair, and avoiding jewellery, including rings, when operating engineering machinery. It also says many serious workshop accidents could be avoided if gloves were not worn near rotating machinery such as drills and lathes.

    Follow the instructions for your drill or drilling machine and your own risk assessment. Keep hands clear of the bit while it is turning.

    How should I secure the work and protect my eyes when drilling steel?icon-minus-redicon-plus-red

    Always clamp the workpiece firmly so the bit cannot grab it and spin it round, rather than holding it by hand. Loose workpieces are a serious safety risk.

    Drilling throws off sharp, hot swarf. The HSE lists projectiles and metal splash among eye hazards and says eye protection should be suited to the task and fit properly. Depending on your risk assessment that may mean safety spectacles, goggles or a face shield. Clear swarf only after the drill has stopped, using a brush or hook, not bare hands.

    Do I need cutting fluid when drilling steel, and how do I use it?icon-minus-redicon-plus-red

    For steel, and especially stainless, cutting fluid is normally worthwhile. It carries heat away, reduces friction and helps the swarf clear. Apply it continuously if you can, or stop regularly to reapply it, rather than letting the bit run dry.

    Use a proper cutting oil or metalworking fluid; thin sprays tend to evaporate quickly. Aluminium and brass can often be drilled with a light lubricant or dry, depending on the material and the job. Follow the bit maker's advice for the material you are drilling.

    Shop Similar Categories