WE HAVE SOME GREAT LIMITED-TIME OFFERS - CLICK HERE TO VIEW THEM WE SHIP WORLDWIDE    /    All UK ORDERS GREATER THAN £75 EX VAT DELIVERED FREE    /    WE SHIP WORLDWIDE    /    ALL EUROPEAN ORDERS GREATER THAN £500.00 ex VAT DELIVERED FREE    /    WE SHIP WORLDWIDE
    Share this page on Facebook   Share this page on LinkedIn   Share this page on Twitter   Share this page on Whatsapp   

    Rapid Ref : 209010-SET4  

    HMT VersaDrive Cobalt Drill Bit InsertFoam 7 Piece Set (12, 13, 14, 16, 18, 20, 22mm)
    209010-SET4

    Click here to see what's included

    £366.56  EX VAT
    SSP Suggested Selling Price = £431.25  YOU SAVE £64.69
     Buy in 3 easy interest free payments of £122.19† with

    SIMPLY THE BEST LONG-LIFE TWIST DRILL BITS FOR METAL.

    All VersaDrive Drill Bits can be used in any standard 1/2" drill chuck for cordless or pistol drill use or adapted for use in a Magnet Drill or Impact Wrench.

    Fast drilling with minimal kickback; dual hardened for impact wrench use up to 10mm. Precision Ground Flutes with deep web design for easy chip clearance. 135 Split Point for easy starting and high accuracy 8% Cobalt for long life and endurance in structural steel and hard metals. GoldMax Low Friction Titanium Coating to Stop Heat Burnout. High Strength, Non-Slip Shank Design.

    Product Details

    Brochures & Manuals

    BROCHURES & MANUALS
       View Brochure

    HMT Drill Bits FAQs

    Answers to common questions about choosing and using cobalt, impact and general purpose drill bits for steel.

    What loose clothing, hair or glove precautions apply when drilling?icon-minus-redicon-plus-red

    Drills are rotating machinery, and entanglement is a serious risk. The HSE advises avoiding loose or baggy clothing, tying back or covering long hair, and avoiding jewellery, including rings, when operating engineering machinery. It also says many serious workshop accidents could be avoided if gloves were not worn near rotating machinery such as drills and lathes.

    Follow the instructions for your drill or drilling machine and your own risk assessment. Keep hands clear of the bit while it is turning.

    Do I need cutting fluid when drilling steel, and how do I use it?icon-minus-redicon-plus-red

    For steel, and especially stainless, cutting fluid is normally worthwhile. It carries heat away, reduces friction and helps the swarf clear. Apply it continuously if you can, or stop regularly to reapply it, rather than letting the bit run dry.

    Use a proper cutting oil or metalworking fluid; thin sprays tend to evaporate quickly. Aluminium and brass can often be drilled with a light lubricant or dry, depending on the material and the job. Follow the bit maker's advice for the material you are drilling.

    What is the difference between cobalt and standard HSS drill bits?icon-minus-redicon-plus-red

    Cobalt steel is a variation of high speed steel with a higher cobalt content, usually described by grades with roughly 5 and 8 per cent cobalt. The cobalt gives much better red hardness, meaning the bit keeps its hardness at high cutting temperatures, so cobalt bits suit tough jobs such as stainless steel, hard steel, cast iron and high-tensile bolts.

    Standard HSS is usually adequate for mild steel, aluminium, brass and plastics. Cobalt bits are often a little more brittle, so avoid side-loading them and do not drill at an angle. Because grades vary, check the markings and the maker's guidance for your material.

    What drill size do I need before tapping a thread?icon-minus-redicon-plus-red

    The hole before tapping must be a specific 'tap drill' size, slightly smaller than the thread's nominal diameter, to leave material for the thread to form. A tool maker explains that a hole that is too small forces the tap to remove too much material and risks binding and breaking it, while one that is too large gives shallow threads that can strip.

    Charts often assume a high thread percentage, and a lower percentage that allows a slightly larger drill can make tapping easier. Charts also differ with whether the tap cuts or forms the thread, so use the chart supplied with your tap or the tap maker's data. Drill the hole straight and square to the surface.

    Shop Similar Categories