WE HAVE SOME GREAT LIMITED-TIME OFFERS - CLICK HERE TO VIEW THEM WE SHIP WORLDWIDE    /    All UK ORDERS GREATER THAN £75 EX VAT DELIVERED FREE    /    WE SHIP WORLDWIDE    /    ALL EUROPEAN ORDERS GREATER THAN £500.00 ex VAT DELIVERED FREE    /    WE SHIP WORLDWIDE
    Share this page on Facebook   Share this page on LinkedIn   Share this page on Twitter   Share this page on Whatsapp   

    Rapid Ref : 301126  

    HMT VersaDrive Impacta DrillTap - UNC Inch Sizes
    301126

    Select Option 
    Prices From £34.43 ex VAT

    VersaDrive Combi Drill Taps are a time-saving solution for pilot drilling & tapping in one easy operation. The Titanium coating provides wear resistance and faster cutting performance. VersaDrive Sheet Metal Impacta-DrillTaps have a patented non-slip Hex shank suitable for use in any standard 1/2” drill chuck for cordless or pistol drills or used with a VersaDrive Rapid Lock adaptor for use in a wide range of power tools such as Magnetic Drills. Recommended for use with Impact Drivers for high drilling and tapping productivity.

    Features

    • Ground flute twist drill creates the perfect tapping hole
    • Safer tapping with minimal kickback
    • Specially hardened for impact wrench use
    • High-grade tool steel for high accuracy & long life
    • Goldmax low friction titanium coating to stop burnout
    • High strength, non-slip shank design
    • Drill & Tap in one easy operation

    Product Details

    Brochures & Manuals

    BROCHURES & MANUALS
       View Brochure

    HMT Drill Taps FAQs

    Answers to common questions about combination drill-taps that drill and thread a hole in a single operation.

    What is a combination drill-tap and what does it do?icon-minus-redicon-plus-red

    A combination drill-tap is a single tool with a drill point at the front and a tap section behind it. It drills the hole, usually forms a small lead-in chamfer, and then cuts the thread, all in one pass without changing tools.

    Because the hole and the thread are cut by the same tool in the same setup, they stay in line with each other. The drill diameter is chosen to suit the thread size, so you do not need to look up a separate tap drill for each job. It is mainly used where a lot of threaded holes are needed quickly, such as fabrication and maintenance work.

    Why do drill-taps break and how can I avoid it?icon-minus-redicon-plus-red

    Most breakages come from the torque rising faster than the tool can take. Common causes are chips packing in the flutes, poor alignment, too little lubrication, running too fast, a worn tool, and the tap running out of depth in a blind hole.

    To reduce the risk, keep the tool square to the surface, use plenty of suitable fluid, let the tool cut at a steady controlled speed, and back out briefly to clear chips if it starts to bind. Use a torque-limiting clutch or setting where your equipment has one, and replace worn tools before they start to struggle. If a tool breaks repeatedly, check the setup and the lubrication before blaming the tool.

    Can I use a drill-tap in a blind hole?icon-minus-redicon-plus-red

    It depends on the design, so check the maker's instructions for your tool. Some combination tools are specifically recommended for through holes only, because the chips have nowhere to go at the bottom of a blind hole.

    If a blind hole is unavoidable, remember that the drill point and the unthreaded lead-in reduce the useful thread depth, and chips build up at the bottom and reduce it further. Allow extra depth beyond the thread you need, clear swarf regularly, and never drive the tool into the bottom of the hole, because that is a common way to break it. For deep blind holes, a separate drill and a spiral-flute tap are often the safer approach.

    How do I choose the right thread size and type?icon-minus-redicon-plus-red

    Choose the thread to match the bolt, stud or fitting that will go into it. That means matching both the diameter and the pitch, and also the thread form: metric, UNC (unified coarse inch) and BSW (Whitworth) are not interchangeable even when the sizes look close.

    Metric pitch is given in millimetres, while inch threads are given as threads per inch. A pitch gauge and calipers on the mating male thread will tell you what you have. A quick check is that a correct bolt should start by hand for several turns; if it does not, it is the wrong thread. Do not force a mismatched thread, as that risks cross-threading and a weak joint.

    Shop Similar Categories