WE HAVE SOME GREAT LIMITED-TIME OFFERS - CLICK HERE TO VIEW THEM WE SHIP WORLDWIDE    /    All UK ORDERS GREATER THAN £75 EX VAT DELIVERED FREE    /    WE SHIP WORLDWIDE    /    ALL EUROPEAN ORDERS GREATER THAN £500.00 ex VAT DELIVERED FREE    /    WE SHIP WORLDWIDE
    Share this page on Facebook   Share this page on LinkedIn   Share this page on Twitter   Share this page on Whatsapp   

    Rapid Ref : 501040  

    HMT VersaDrive Reamer - Inch Sizes
    501040

    Select Option 
    Prices From £62.52 ex VAT

    HMT VersaDrive Reamers perform the fastest and with less kickback when adapted with an Impact wrench for enlarging holes in steel plate up to around 20mm thick. However, they can also be used in any standard 1/2" cordless or pistol drill chuck or adapted for a slow-speed Magnet Drill. Ideal for use on plate heavier than 20mm thick. 

    VersaDrive™ reamers are not recommended for use with laser or plasma cut holes. The heat-affected holes can be enlarged using the VersaDrive reamer with a slow-speed magnet drill.

    Precision 6-Flute design for a smooth cut on structural steel. Safer reaming with minimal kickback, specially hardened for impact wrench use. High-grade tool Steel with ground flutes for high accuracy & long life. GoldMax low friction Titanium Coating to stop heat burnout. High Strength, Non-slip shank design.

    Product Details

    Brochures & Manuals

    BROCHURES & MANUALS
       View Brochure

    HMT Reamers FAQs

    Answers to common questions about choosing and using reamers for enlarging and aligning holes in steelwork.

    Can a reamer fix a hole that is in the wrong place?icon-minus-redicon-plus-red

    No. A reamer follows the hole that is already there, so it will not correct a hole that is off position or not straight. It can deal with small, local misalignment between plies, but only by removing the minimum material needed.

    If holes are badly out, reaming is the wrong answer and the connection may need to be reviewed by the person responsible for the design. Do not try to fill mislocated holes by welding without that advice.

    How much material should I leave for the reamer to remove?icon-minus-redicon-plus-red

    Too little and the reamer rubs instead of cutting, which creates heat, wears the tool and can leave the hole undersize. Too much and the hole can end up oversize with a rough finish.

    For machine reaming, the allowance usually depends on the material, the hole diameter and the finish of the pre-drilled hole, and is typically a small percentage of the diameter. The reamer maker's guidance is the best starting point for the exact amount, and for site work on structural joints follow the job specification.

    Why does my reamer chatter and how do I stop it?icon-minus-redicon-plus-red

    Chatter spoils the hole finish and damages the reamer. Common causes are a loose workpiece, play in the tool or tool holder, too much overhang, and the wrong speed or feed pressure.

    Clamp the work firmly, keep the reamer square to the hole and well supported, and avoid forcing it. If chatter continues, check the speed and feed against the maker's guidance, and make sure the hole you started with is straight and not badly off-centre.

    What eye protection should I wear when reaming?icon-minus-redicon-plus-red

    Wear eye protection suited to the job. The HSE lists working with power-driven tools, where debris or chippings may fly into the face, as a case where eye protection is needed, and says it should be appropriate for the task and fit the wearer properly.

    Safety glasses with side protection are the minimum for most reaming; goggles or a face shield may be better where chips are thrown. Do not use compressed air to blow swarf away, because it can bounce back into the eyes. Use a brush or a vacuum instead, with the tool stopped.

    Shop Similar Categories