WE HAVE SOME GREAT LIMITED-TIME OFFERS - CLICK HERE TO VIEW THEM WE SHIP WORLDWIDE    /    All UK ORDERS GREATER THAN £75 EX VAT DELIVERED FREE    /    WE SHIP WORLDWIDE    /    ALL EUROPEAN ORDERS GREATER THAN £500.00 ex VAT DELIVERED FREE    /    WE SHIP WORLDWIDE
    Share this page on Facebook   Share this page on LinkedIn   Share this page on Twitter   Share this page on Whatsapp   

    Rapid Ref : 790094010  

    REB 20, Pipe End Preparation Machine, Pneumatic Drive, Pipe OD 290 - 508mm
    790094010

    Click here to see what's included

    £14250.00  EX VAT
     Buy in 3 easy interest free payments of £4750.00† with

    The most powerful pipe end preparation solution. Counterboring and axial turning of pipes made from high-alloy steel (stainless steel), low-alloy and carbon steel with the unique tool system QTC. Up to four tools can be used at the same time.

    The machine comes with:

    • 1 Transportation case
    • 2 Clamping chucks
    • 6 Clamping sets, each with three clamping wedges
    • 1 Toolset
    • 1 KSS-TOP lubricant spray pump (Code 790060226)
    • 1 Set of operating instructions and spare parts list

    Pneumatic power drive:

    Power: 1.8kW (2.45hp), Air supply requirement: 2m³ /min at 6 bar (70.6cfm at 90 PSI).  Nominal speed range: 0 - 13 rpm.

    Note: The manufacturer's warranty can only be given when using the original DWE-10 mobile air unit from Orbitalum, see related items.

    Brochures & Manuals

    What's Included

    790060226  Orbitalum Cutting Lubrication KSS-TOP, Pump Sprayer with 500ml

    Orbitalum Cutting Lubrication KSS-TOP, Pump Sprayer with 500ml

    ORB-MANUAL  Orbitalum Operating Manual and Spare Parts List

    Orbitalum Operating Manual and Spare Parts List

    REB-6CLAMP  6 x Orbitalum clamping sets, each with 3 clamping wedges

    6 x Orbitalum clamping sets, each with 3 clamping wedges

    REB-CHUCK2  2 x Orbitalum REB Clamping Chuck

    2 x Orbitalum REB Clamping Chuck

    Related Items

    REB Pipe Bevelling Machines FAQs

    Answers to common questions about inside-clamped pipe end preparation machines with a pneumatic drive, used to bevel and face pipe ends before welding.

    What does a pipe end preparation machine do?icon-minus-redicon-plus-red

    It prepares the end of a pipe for welding by cutting a bevel and facing the end square, using a rotating tool head. The machine is clamped inside the bore of the pipe, so the cut runs true to the pipe and each end can be prepared the same way.

    For larger pipe a multi-edged cutting tool can usually be used for different operations, such as facing and bevelling, and on different wall thicknesses and materials. Check the maker's instructions for the pipe sizes, wall thicknesses and materials your machine is approved for, because these limits are specific to each machine and are on the data plate and in the manual.

    How do I choose the right clamping wedges and chuck?icon-minus-redicon-plus-red

    These machines grip the inside of the pipe, so the clamping parts are chosen by the pipe's inside diameter, not its outside size. Work out the bore first (outside diameter less twice the wall thickness), then pick the wedge set and clamping chuck whose range covers it. Ranges overlap in steps, so choose the set where your bore sits comfortably within the range rather than at the very edge.

    The maker's manual has a table matching bore ranges to wedges and chucks. After clamping, centre the mandrel in the pipe and check it is firm before you start, and keep the wedges and their seats clean so they grip evenly.

    Does the pipe need to be cut square before I use the machine?icon-minus-redicon-plus-red

    It helps a great deal. The machine faces and bevels, but it is not meant to fix a badly angled saw cut. The maker warns that a pipe which is not sawn off square can damage the tool if the cutting edge starts too close to the pipe end, so before switching on, check there is enough clearance between the edge and the pipe end.

    Feed the tool in slowly until it first touches, then keep an even pressure once the edge is cutting all the way round. Rushing the first contact is a common cause of a chipped edge and a rough start to the cut.

    Do I need cutting lubricant, and which one should I use?icon-minus-redicon-plus-red

    Yes. Machining with lubrication generally extends the life of the cutting tools and allows a larger feed rate. Use the type of cutting lubricant the machine maker recommends in the manual rather than a general oil.

    Apply it at the cutting area during the cut, and be careful with chip removal afterwards. Lack of lubrication is one of the causes the maker lists for poor surface quality on cut and bevelled faces, so if your finish looks rough or the tool is wearing quickly, check lubrication before anything else.

    Shop Similar Categories