WE HAVE SOME GREAT LIMITED-TIME OFFERS - CLICK HERE TO VIEW THEM WE SHIP WORLDWIDE    /    All UK ORDERS GREATER THAN £75 EX VAT DELIVERED FREE    /    WE SHIP WORLDWIDE    /    ALL EUROPEAN ORDERS GREATER THAN £500.00 ex VAT DELIVERED FREE    /    WE SHIP WORLDWIDE
    Share this page on Facebook   Share this page on LinkedIn   Share this page on Twitter   Share this page on Whatsapp   

    Rapid Ref : 790094013  

    Orbitalum ID Tracking Kit for REB 14 & REB 20
    790094013

    £1425.00  EX VAT
     Buy in 3 easy interest free payments of £475.00† with

    The REB ID tracking can be used to prepare thin-walled, large-scale pipes for welding, where precise pipe-end preparation and exact base width are required.

    The module measures the pipe ID. The force of the spring on the inside diameter ensures that the roller "tracks" any irregularities of the pipe, producing a weld prep exactly by the ID, thus maintaining a perfect weld prep. All weld preparations such as V-, Y0, and U- preps can be realised with the ID tracking module.

    Comes with:

    • ID tracking module
    • Mount for plane
    • Assembly instructions

    Specifications

    REB 14 - Pipe ID:150 - 320mm, Wall thickness max: 15mm
    REB 20 - Pipe ID:290 - 500mm, Wall thickness max: 10mm

    Orbitalum Accessories for BRB / REB machines FAQs

    Answers on the clamping, lubrication and air-supply accessories used with portable pipe end preparation machines.

    What are the health risks of cutting fluids and how do I reduce them?icon-minus-redicon-plus-red

    The HSE says skin contact with metalworking fluids can cause dermatitis, mainly on the hands and arms, and that breathing in the mist can cause lung problems such as occupational asthma. Its key messages are to prevent or limit skin contact, to prevent or control airborne mist, and to keep the fluid in good condition.

    In practice that means using only the amount you need, avoiding soaked clothing, washing fluid off the skin, and reading the product's safety data sheet. Your risk assessment should decide what protective equipment and ventilation are needed.

    Why is the bevel angle and finish important before welding?icon-minus-redicon-plus-red

    Bevelling the pipe ends gives access to all parts of the joint, so the weld can fuse properly right through. Single-sided joints need dimensionally accurate preparation and fit-up, the included angle is what matters for access, and if the angle or gap is too small there is not enough room to hold a correct arc length.

    The angle, root face and gap that you need are set by your weld procedure and the standard for the job, so check those before you set up the machine. A clean, even, burr-free finish also helps the pipe ends fit together properly, so check the finished prep before you move on.

    What are optional clamping wedges for?icon-minus-redicon-plus-red

    Clamping wedges are the parts that actually contact the pipe bore. A standard set covers a stated range of bore sizes, and makers list optional wedge sets specifically for extending that range, each shown against the pipe inside diameter it suits, so the same machine can take larger bores.

    Choose them by the inside diameter of the pipe, which depends on the outside diameter and the wall thickness, not by the nominal pipe size alone. Measure the bore if you are unsure, and check the machine's manual for which wedge set matches which bore range. Do not use a set outside its stated range.

    What should I check on the air hose and quick couplings?icon-minus-redicon-plus-red

    If your machine is air-driven, check the hose before each use for cuts, bulges, abrasion and other damage, and tag and replace any defective hose straight away. Safety guidance recommends a safety cable or whip check to stop the hose moving uncontrollably if a connection fails, and a mechanical lock on connections.

    Never run hose, couplings or the machine above the maker's pressure rating, make sure couplings are fully engaged and clean, and do not run the hose where it can be trodden on. The HSE has guidance on compressed air safety that covers portable pneumatic equipment, including inspection, maintenance and training.

    Shop Similar Categories