WE HAVE SOME GREAT LIMITED-TIME OFFERS - CLICK HERE TO VIEW THEM WE SHIP WORLDWIDE    /    All UK ORDERS GREATER THAN £75 EX VAT DELIVERED FREE    /    WE SHIP WORLDWIDE    /    ALL EUROPEAN ORDERS GREATER THAN £500.00 ex VAT DELIVERED FREE    /    WE SHIP WORLDWIDE
    Share this page on Facebook   Share this page on LinkedIn   Share this page on Twitter   Share this page on Whatsapp   

    Rapid Ref : ETOP2-IMPACT  Mfr Ref : STC-ETOP2-IMPACT

    HMT VersaDrive STAKIT Top Tool Case - ETOP2 Turbo Impact Starter Kit
    STC-ETOP2-IMPACT ETOP2-IMPACT

    Click here to see what's included

    £456.88  EX VAT
    SSP Suggested Selling Price = £537.50  YOU SAVE £80.62
     Buy in 3 easy interest free payments of £152.29† with

    This product is included in the latest promotion from HMT! Valid until December 21st, save £170.60 with this limited time offer. HMT OD26 VersaDrive STAKIT ETOP2 Turbo Impact Starter Kit

    Compact but fully stocked, the ETOP2 Impact Kit provides all the most needed sizes of drilling, tapping, and enlarging tools for hole creation and modification in the field.

    Kit Contents

    • 4 x VersaDrive TurboTip Impact Drill Bits (6.8, 8.5, 10.5, 14mm)
    • 4 x VersaDrive ImpactaTaps (M8, M10, M12, M16)
    • 3 x VersaDrive ImpactStep Cutters (8-16mm, 14-22mm & 18-26mm)
    • 1 x VersaDrive Rapid-Lock ½” Impact Wrench Adaptor
    • 1 x VersaDrive 130mm Extension Arbor
    • 1 x VersaDrive STAKIT Half Top Case

    Product Details

    HMT Step Drills FAQs

    Answers to common questions about choosing and using step drills for clean, accurate holes in thin sheet material.

    How does a step drill compare with a twist drill on sheet metal?icon-minus-redicon-plus-red

    On thin sheet, a twist drill can grab, wander and leave a rough or slightly out-of-round hole with a burr around the edge. A step drill cuts one diameter at a time, so the hole is usually round and cylindrical, and each step tends to clean up the edge left by the step before it.

    A twist drill is still the better choice for thicker material, for deep holes and for sizes that fall between the steps. Choose according to the thickness and material you drill most often.

    How thick a material can a step drill cut?icon-minus-redicon-plus-red

    Step drills are designed for thin material, and makers state a maximum thickness for each bit or set. The figure varies widely: general-purpose bits are often rated for only a few millimetres of sheet, and some cobalt bits are rated for sheet steel gauges around 2 to 3.5 mm, with stainless steel often rated lower.

    The limit depends on the bit, the material and the power of the drill. Thicker plate is better drilled with a twist drill, often starting with a small pilot hole. Always check the limit stated by the maker for your particular bit.

    What if I need a hole size between two steps?icon-minus-redicon-plus-red

    A step drill cuts fixed diameters, so it cannot make a size that falls between two steps. The usual options are to use the next step up if the larger hole is acceptable, to drill with a twist drill of the exact size, or to use a tapered sheet-metal cone drill, which enlarges a hole steplessly.

    Check the sizes marked on the bit before you buy, as step drills are made in metric and in inch sizes, and make sure the steps match the holes you need, for example for glands, conduit or fixings.

    What speed and pressure should I use with a step drill?icon-minus-redicon-plus-red

    Speed depends on the material. Makers and tool guides generally advise a low speed for stainless steel and other hard metals, and a higher speed for mild steel, with plastics usually run faster but watched for heat. Slow down as the bit reaches the larger steps. Use light, steady pressure and let the cutting edges do the work; excessive force overheats the bit and distorts the hole.

    A variable-speed drill makes this much easier. Exact speeds differ between makers and materials, so use the figures supplied with the bit as your starting point.

    Shop Similar Categories