SHOW PRICES INCLUDING VAT
Trustpilot
Click to visit the Rapid Blog - Supporting welders every step of the way
0Your Basket : £ 0.00
WE HAVE SOME GREAT LIMITED-TIME OFFERS - CLICK HERE TO VIEW THEM WE SHIP WORLDWIDE    /    All UK ORDERS GREATER THAN £75 EX VAT DELIVERED FREE    /    WE SHIP WORLDWIDE    /    ALL EUROPEAN ORDERS GREATER THAN £500.00 ex VAT DELIVERED FREE    /    WE SHIP WORLDWIDE
H2122 Harris Shank 43-2
    Share this page on Facebook   Share this page on LinkedIn   Share this page on Twitter   Share this page on Whatsapp   

    Rapid Ref : H2122  Mfr Ref : 1401254

    Harris Shank 43-2
    1401254 H2122

    £128.72  EX VAT
    SSP Suggested Selling Price = £143.00  YOU SAVE £14.28
     Buy in 3 easy interest free payments of £42.91† with

    This model is a high-capacity combination handle. With proper accessories, it can be used for either acetylene or other fuel gases.

    Related Items

    Harris 43-2 Acetylene FAQs

    Answers to common questions about the nozzles, mixers, heating heads and cutting attachments used with a modular oxy-acetylene torch.

    What pressure should I run acetylene at?icon-minus-redicon-plus-red

    For most welding and cutting jobs the HSE says acetylene pressure should not exceed 0.62 bar (9 psi), unless the equipment has been specifically designed for a higher pressure. Decomposition of acetylene can be triggered more easily and proceed more rapidly if the gas in the hoses is above the pressure recommended by the supplier, so do not simply wind the regulator up to get more heat.

    The right working setting for a particular nozzle or mixer is on the manufacturer's chart or data plate. Use only a regulator, hoses and torch parts made for acetylene and marked to the correct standards, and follow your own risk assessment.

    What causes backfires and flashbacks, and how do I reduce them?icon-minus-redicon-plus-red

    The HSE says poorly maintained nozzles cause turbulent gas flow, which increases the risk of flashback. Inspect nozzles regularly, make sure they are not blocked by dirt or spatter, and replace damaged ones. Holding the nozzle too close to the workpiece can overheat it and cause a flashback.

    A flashback can also happen if a flammable mixture of fuel gas and oxygen is left in the hoses when the torch is lit, which is why purging matters. Tips and mixers that are loose or not properly seated are another common problem, so tighten them by hand or as the maker instructs.

    How should acetylene cylinders be handled and stored?icon-minus-redicon-plus-red

    An acetylene cylinder contains a porous mass soaked in acetone, so it is built differently from most gas cylinders. HSE guidance says not to drop or jar it and not to roll it across the floor. Keep it upright, and if it has been laid down and returned to upright, leave it for an hour to settle before use.

    Check the identification and look for damage before use, and turn off all valves after use. In the UK, acetylene cylinders are normally painted maroon, but the label is what identifies the gas. If a cylinder looks damaged, the label is unclear, or it has been involved in a fire or flashback, do not use it and speak to your gas supplier.

    How do I choose the right cutting nozzle?icon-minus-redicon-plus-red

    The cutting oxygen bore is chosen by the thickness of material, so larger bores are used on heavier plate. Nozzles are made as one-piece or two-piece designs, and the choice depends on the fuel gas, whether the torch is hand or machine operated, and the maker's design. Standard nozzles have a central oxygen bore surrounded by preheat ports.

    Always match the nozzle to the fuel gas and to the torch or cutting attachment it was made for. The maker's chart gives the recommended gas pressures for each size, so check it rather than guessing from a similar tip.

    See all 6 questions for this category

    Shop Similar Categories