WE HAVE SOME GREAT LIMITED-TIME OFFERS - CLICK HERE TO VIEW THEM WE SHIP WORLDWIDE    /    All UK ORDERS GREATER THAN £75 EX VAT DELIVERED FREE    /    WE SHIP WORLDWIDE    /    ALL EUROPEAN ORDERS GREATER THAN £500.00 ex VAT DELIVERED FREE    /    WE SHIP WORLDWIDE
    Share this page on Facebook   Share this page on LinkedIn   Share this page on Twitter   Share this page on Whatsapp   

    Rapid Ref : RG-240  Mfr Ref : 92501124

    Tweco Roto-Ground Heavy Duty Rotary Earth Clamp - 800 Amp
    92501124 RG-240

    £630.74  EX VAT
    SSP Suggested Selling Price = £700.82  YOU SAVE £70.08
     Buy in 3 easy interest free payments of £210.25† with

    Tweco® Roto-Ground is a highly efficient device for grounding weldments while rotating on turning rolls or positioners. The 2" shaft shoulders up to a steel nut, which the user welds to his rotating work or fixture. Tweco Roto-Grounds have no brushes, springs or mercury. A simple tension-adjusting bolt provides maximum efficiency.

    Specification

    • Amperage Capacity: 800A
    • Cable Capacity: 2 – 4/0
    • Number of Heads: 1
    • Shaft Stud: 1-3/8” NC
    • Length: 270mm (10-5/8”)
    • Weight: 4.527Kg

    Brochures & Manuals

    BROCHURES & MANUALS
       View Brochure

    Rotary Earth Clamps FAQs

    Answers on how rotary earth clamps work, how to choose one and how to keep the return path safe while the work turns.

    What is a rotary earth clamp and how does it work?icon-minus-redicon-plus-red

    A rotary earth clamp is a return clamp with a rotating joint between the part that grips the work and the part that takes the welding cable. The clamp turns with the workpiece, while the cable side stays still.

    This lets welding current pass across the rotating joint into the work, so you can weld a pipe, vessel or other round part as it turns on a positioner or rollers without the return cable wrapping up. Ratings and the types of cable connection vary between models, so check the product details for yours.

    Why not just use a standard clamp on a part that turns?icon-minus-redicon-plus-red

    A standard clamp has a fixed cable, so as the work rotates the cable winds around the part, twists and can be pulled off or damaged. Constant movement can also make the contact unreliable, and that causes an unstable arc.

    A rotary clamp lets the part turn while the cable stays put. It is not needed for work that stays still. Our team can help you choose one that suits your positioner or rollers.

    Why does welding current need to avoid bearings?icon-minus-redicon-plus-red

    Welding current will take any route back to the machine, including routes you did not intend. TWI lists wire ropes, slings and chains and bearings in motors among the unintended paths that welding current can use.

    Bearings in positioners and rollers are not designed to carry welding current, and arcing inside them can damage them. A rotary clamp gives the current a deliberate path across the rotating joint, so it does not need to cross the bearings. Check your positioner's manual for how the maker recommends connecting the return.

    How do I choose the right current rating?icon-minus-redicon-plus-red

    Match the clamp to the highest welding current and duty cycle you will use, and leave some margin rather than running it at its limit. Welding cable and connectors must be insulated and thick enough to carry the current safely, and the clamp is part of that same path.

    Cable size depends on the machine's output, its duty cycle and the total length of the circuit. Look at the machine's rating plate and manual, and make sure the clamp's rating is shown on the product. Where the work will be heavy, repeated or long runs, choose the higher rating.

    Shop Similar Categories