WE HAVE SOME GREAT LIMITED-TIME OFFERS - CLICK HERE TO VIEW THEM WE SHIP WORLDWIDE    /    All UK ORDERS GREATER THAN £75 EX VAT DELIVERED FREE    /    WE SHIP WORLDWIDE    /    ALL EUROPEAN ORDERS GREATER THAN £500.00 ex VAT DELIVERED FREE    /    WE SHIP WORLDWIDE
    Share this page on Facebook   Share this page on LinkedIn   Share this page on Twitter   Share this page on Whatsapp   

    Rapid Ref : SPXX  

    Speedy Inflatable Purge Bag System, 8 - 38" (203 - 965mm)
    SPXX

    Select Option 
    Prices From £339.00 ex VAT

    The GBC Speedy Purge System for pipe and vessel purging comprises a tandem inflatable dam system connected by an umbilical hose and collar to reduce the volume being purged. A gas exhaust valve is installed between the primary and secondary dam and an auxiliary Argon purge line.

    The system is positioned by viewing the luminous tape through the weld joint gap. E-Z ZONE TAPE is used to seal the weld gap and purge gas flow can commence at up to 20 Ltr/min. The bags inflate, a seal is created on either side of the weld joint, and the pressure valve releases gas into the weld chamber. By using a GBC Oxygen Monitor to constantly measure the oxygen content in the weld chamber the welder will know when to reduce the gas flow and commence welding.

    The system is left in position post-welding until the weld joint temperature drops to below oxidation levels, then the purge gas feed is disconnected, the bags deflate, and the system can be withdrawn.

    Brochures & Manuals

    BROCHURES & MANUALS
       View Brochure

    Speedy Purge Systems FAQs

    Practical answers on choosing, setting up and looking after twin-dam inflatable purge bag systems, including heat-resistant versions.

    How does a twin inflatable purge bag system work?icon-minus-redicon-plus-red

    A twin-dam system has two inflatable bags joined by a connecting tube. You position it so the weld joint sits between the bags, inflate them so they seal against the pipe wall, then feed purge gas into the sealed space between them to push out the air. Only the short length around the joint is purged, so less gas is usually needed than purging a whole pipe run.

    Many systems fill the bags and the purge space from a single gas connection, with a valve that lets the bags seal before gas enters the chamber. Check the maker's instructions for how your system is set up.

    How do I choose the right size of bag system for my pipe?icon-minus-redicon-plus-red

    Bag systems are sold in size ranges, and the range refers to the inside diameter (bore) of the pipe, not just its nominal size. The wall thickness changes the bore: the inside diameter is the outside diameter minus twice the wall thickness, so heavier-wall pipe of the same nominal size has a smaller bore.

    Measure or calculate the actual bore and pick the system whose stated range covers it, ideally with the bore sitting comfortably inside the range rather than at the very edge. Your supplier's size chart and the maker's instructions are the final word.

    What does a heat-resistant purge system mean, and how hot can it go?icon-minus-redicon-plus-red

    A heat-resistant system uses bag material intended to cope with the heat that travels along the pipe from the weld, and sometimes from preheating. Ratings vary widely between products, and some are quoted as a continuous figure while others allow a higher temperature only for short periods.

    Always read the temperature rating for your particular system, note whether it is continuous or short-term, and keep the bags well back from the heat source. Heat is a recognised cause of inflatable dams swelling beyond their safe limits, so do not assume a bag will tolerate any weld.

    Why do purge bags burst, and how can I prevent it?icon-minus-redicon-plus-red

    Bags can burst when they are over-pressurised. As the heat of welding rises, the inflatable dams can expand beyond their safe limits, and someone changing the gas flow or pressure near the weld can over-inflate them. A burst ends the purge and the weld oxidises as soon as air gets in.

    Keep the regulator and flow settings protected from casual adjustment, follow the maker's inflation guidance, and consider a pressure-limiting or relief device in the supply line if the maker recommends one. Never bypass the regulator to speed up the purge.

    Shop Similar Categories