WE HAVE SOME GREAT LIMITED-TIME OFFERS - CLICK HERE TO VIEW THEM WE SHIP WORLDWIDE    /    All UK ORDERS GREATER THAN £75 EX VAT DELIVERED FREE    /    WE SHIP WORLDWIDE    /    ALL EUROPEAN ORDERS GREATER THAN £500.00 ex VAT DELIVERED FREE    /    WE SHIP WORLDWIDE

CK 2 Series Gas Lens Parts

CK 2 Series Gas Lens Spares

CK 2 Series Gas Lens Parts FAQs

Gas lens bodies, cups, collets and related parts for this torch type, and how to pick and look after them.

What does a gas lens do that a standard collet body does not?icon-minus-redicon-plus-red

A standard collet body sends shielding gas out through a ring of small holes. A gas lens makes the gas pass through fine mesh screens first, which gives a smoother, less turbulent flow and a more even coverage pattern at the weld.

Makers describe the benefits as reduced turbulence, better gas coverage and the ability to run more tungsten stick-out. The practical gain is clearest when you need to reach into corners or want a longer electrode for visibility. With a short stick-out the difference can be hard to see, so a gas lens is a useful upgrade rather than a must-have for every job.

What parts make up a gas lens set-up?icon-minus-redicon-plus-red

A gas lens front end normally consists of the gas lens body itself, a cup made for it, a collet to grip the tungsten, a heatshield (insulator) and a backcap with its O-ring. The gas lens takes the place of the standard collet body, while you still need a matching collet.

Because these parts are designed to work together, treat the set as a system. Mixing a gas lens with the wrong cup or collet can leave a poor seal or a poor grip on the electrode. Check the parts list in your torch manual to see which items belong with your torch type, and replace worn items in the set together where practical.

How do I choose the right size of gas lens and collet?icon-minus-redicon-plus-red

Choose by tungsten diameter and by torch type. The size of the collet and the gas lens is set by the diameter of the electrode, so an electrode of a given diameter needs a gas lens and collet marked for that same diameter. The torch type also matters, because the head thread and body length differ between torch types.

Check the size marking on the old part and compare it with the chart in your manual, which normally lists the electrode diameters and the matching parts. Do not try to force an electrode into a collet of a different size: a poor grip causes a bad arc and heat build-up at the contact. If you change electrode diameter often, keep a matching set for each size.

Which cup fits a gas lens, and does cup size matter?icon-minus-redicon-plus-red

Cups for gas lenses are not the same as cups for standard collet bodies. The two bodies have different sizes and thread patterns, so each needs its own cup. Always order a cup made for the gas lens, not just one with the right opening size.

The cup opening affects coverage: a larger opening gives broader gas coverage, while a smaller one gives better access to tight spots. Larger-diameter electrodes run at higher current and normally go with larger cups. Pick the smallest cup that still covers the weld well. A larger cup can block your view or restrict access, and a gas lens is often paired with a bigger cup to take full advantage of the smoother flow.

Alumina, ceramic or clear cups - which should I use?icon-minus-redicon-plus-red

Alumina cups are the general-purpose choice and cope well with knocks. Lava (ceramic) cups are normally recommended where reflected heat is high, such as in confined corners, because an alumina cup can crack when heat is reflected back at it and it then cools.

Clear glass-type cups let you see the weld pool more clearly and suit work into corners, but they are not well suited to walking the cup on pipe, so check your torch manual for their heat limits. Whichever you choose, make sure it matches your gas lens, and replace any cup with chips or cracks, because a damaged rim can disturb the gas flow. Never touch a cup to a hot workpiece.

How far can I let the tungsten stick out with a gas lens?icon-minus-redicon-plus-red

A gas lens lets you use a longer stick-out than a standard collet body because the gas column is smoother and carries further. That is helpful in tight joints and for seeing the weld.

The actual limit depends on cup size, the work, current and drafts, so use the guidance in your torch manual, and keep it as short as the job allows. A longer electrode puts more of the tungsten outside the gas shield, so the risk of contamination rises, and in a draught the safe length is shorter. Extra pre-flow and post-flow help protect the tungsten, and the equipment must keep gas flowing after the arc stops so the hot electrode and weld cool under shielding gas.