WE HAVE SOME GREAT LIMITED-TIME OFFERS - CLICK HERE TO VIEW THEM WE SHIP WORLDWIDE    /    All UK ORDERS GREATER THAN £75 EX VAT DELIVERED FREE    /    WE SHIP WORLDWIDE    /    ALL EUROPEAN ORDERS GREATER THAN £500.00 ex VAT DELIVERED FREE    /    WE SHIP WORLDWIDE

CK 300 Parts

Parts and consumables for CK 300 Torches.

CK 300 Parts FAQs

Answers to common questions about torch body, cable set and consumable spares for a heavy-duty water-cooled TIG torch.

How do I identify the right replacement part for a heavy-duty water-cooled TIG torch?icon-minus-redicon-plus-red

Begin with the data plate on the torch and the parts list in the manual, which give the torch type and current rating. Then compare the part number or markings on the old item, and measure what you can safely measure, such as tungsten diameter and back cap length.

Torch bodies, handles, cable sets and consumables are normally specific to a torch type and to its cooling method, so a part that looks similar may not fit or may not carry the current. If the old part is unreadable, our team can help you match it before you order.

What is the difference between spares for the torch head and spares for the cable set?icon-minus-redicon-plus-red

The head spares are the consumables that sit around the tungsten: collet, collet body or gas lens, cup, back cap and O-rings. They are exposed to heat and wear fastest. The cable set carries the welding current, shielding gas and coolant to the torch, and normally lasts much longer if it is looked after.

On a water-cooled torch the coolant circulates through the head and returns along the power cable, so a failure at either end can affect cooling. Check which one you actually need before ordering.

How can I tell the power cable and hoses need replacing?icon-minus-redicon-plus-red

Look for cracked, cut, bulging, stiff or discoloured cable and hose covers, melted insulation near the torch, damp patches, and handles that get hot or feel unusually warm. HSE guidance says to check that the insulation on the cables, plugs and torch is undamaged, and welders should report any defects they find.

Do not keep using a torch lead with damaged insulation or exposed conductors. Coolant leaks can hide under the cable jacket, and a leak needs prompt repair. Tape is at best a short-term stop-gap; replacing the damaged section is usually safer. Follow the maker's instructions and your risk assessment.

Why does the handle or cable get hot on a high-current torch?icon-minus-redicon-plus-red

Welding current passing through any conductor produces heat, and on a water-cooled torch the coolant carries it away. If the handle or cable runs hotter than usual, common causes are low or blocked coolant flow, a kinked or damaged hose, a loose connection, or running the torch above its rating.

A torch run beyond its rated output tends to heat the handle and cable faster, which causes downtime. Stop welding, let it cool, and check the coolant circuit and the torch rating on the data plate before restarting.

Is it normal for consumables to last longer on a water-cooled torch?icon-minus-redicon-plus-red

It can help, but do not assume it. Coolant carries heat away from the head, so the collet body, collet and cup generally run cooler than on an air-cooled torch used at the same current. The actual life of each part still depends on the current, the duty cycle, how well the torch is assembled and how clean the work is.

Cups still crack, collets still deform, and O-rings still harden. Inspect them whenever you change the tungsten, replace by condition, and do not assume a part is fine just because the torch is water-cooled. Follow the torch maker's guidance.

How do I choose between a standard collet body and a gas lens on this torch?icon-minus-redicon-plus-red

A standard collet body is simple and fine for general work. A gas lens uses fine mesh screens to smooth the shielding gas, giving more even coverage and letting you extend the tungsten further, which suits critical welds and awkward joints. A gas lens is normally paired with a matching cup, so the two are chosen together.

Whichever you pick, match the collet and body to the tungsten diameter and to the torch type. Do not simply raise the gas flow to make up for poor coverage; set the flow as the torch maker and your welding procedure advise.