WE HAVE SOME GREAT LIMITED-TIME OFFERS - CLICK HERE TO VIEW THEM WE SHIP WORLDWIDE    /    All UK ORDERS GREATER THAN £75 EX VAT DELIVERED FREE    /    WE SHIP WORLDWIDE    /    ALL EUROPEAN ORDERS GREATER THAN £500.00 ex VAT DELIVERED FREE    /    WE SHIP WORLDWIDE

CK300 Torch Parts

CK300 Torch Parts FAQs

Practical answers on choosing, fitting and looking after the torch body, hoses, power cable and back cap for a large water-cooled TIG torch.

Why must coolant be flowing before I strike an arc?icon-minus-redicon-plus-red

In a water-cooled torch the coolant carries heat away from the power cable and torch head. A torch maker's manual warns that insufficient coolant flow can cause permanent damage to the torch, and tells the user to check the cooling function before use. Liquid-cooled cable assemblies can also leak if they overheat.

Before welding, switch the cooler on, check the coolant level and look for coolant returning to the cooler and for leaks at the fittings. Poor flow can come from a blocked filter, a kinked line, crossed connections or a clogged fitting. If the cooler has a flow switch or alarm, never bypass it.

Why does the power cable inside a water-cooled hose fail, and which way should the coolant flow?icon-minus-redicon-plus-red

In many water-cooled torches the power cable runs inside the coolant return hose, so coolant passes along it on its way back to the cooler. A torch maker's troubleshooting guide says that when water-cooled leads wear out quickly you should verify the coolant flow direction: the return flow must be on the power cable lead. Another maker's manual warns that if the coolant connections are crossed the torch may overheat.

Constant flexing can also wear the cable. A cable that runs hot, feels stiff or leaks at the fitting should be checked and normally replaced rather than patched.

What are the signs that a hose or power cable needs replacing?icon-minus-redicon-plus-red

Look for cracking, ballooning or bubbling, thinning walls, cuts, scuffed outer covers, stiffness and drips at the fittings. Welding-equipment makers' manuals say hose packs should be undamaged and securely connected, damaged parts should be replaced immediately, and a leaking hose pack should be replaced because a leak can cause high-frequency flashover.

A cable that gets hot, a hose that kinks easily or coolant that returns weakly can also point to a worn or partly blocked assembly. Do not tape a leaking hose; replace the whole hose or cable assembly.

How do I work out which torch body, hose or cable I need?icon-minus-redicon-plus-red

Start with the data plate on the torch and the manual, which give the torch type and cooling method. Then compare the old part: note any markings, the fitting type and thread, the length and whether it is a water hose, a power cable that also returns coolant, or a gas hose.

Take clear photos of the connectors at both ends. Fittings and threads differ between torch families, so never assume a part from another range will fit. If in doubt, our team can help you match the part to your torch.

What coolant should I use in the cooler?icon-minus-redicon-plus-red

Use the coolant specified by the cooler and torch makers. Advice differs: one trade article says to use only distilled water or an approved welding coolant and never city water, anti-freeze or rust inhibitors, while a torch maker's manual says not to use deionised or demineralised water. Tap water is widely discouraged because it can leave deposits, cause corrosion and clog the torch.

Do not mix coolant types or add other additives unless the manual says so, and drain and refill at the interval it gives. Dirty or degraded coolant is a common cause of clogged torch fittings. If the manuals for the cooler and the torch disagree, ask the makers which coolant to use.

How do I check for gas leaks in the torch and hoses?icon-minus-redicon-plus-red

Air drawn into the gas stream causes porosity. A welding-equipment maker's troubleshooting guide lists a defective gas hose or loose connection among the causes and says to check hoses and connections for leaks. Common places are the back cap O-ring, the torch head seals, loose fittings and a damaged or kinked gas hose.

With the gas on, brush leak-test solution or soapy water on each connection and look for bubbles, or close the gas at the regulator and watch for a pressure drop. Wipe the solution off afterwards and replace any damaged hose rather than taping it.