WE HAVE SOME GREAT LIMITED-TIME OFFERS - CLICK HERE TO VIEW THEM WE SHIP WORLDWIDE    /    All UK ORDERS GREATER THAN £75 EX VAT DELIVERED FREE    /    WE SHIP WORLDWIDE    /    ALL EUROPEAN ORDERS GREATER THAN £500.00 ex VAT DELIVERED FREE    /    WE SHIP WORLDWIDE

Chemical Aids

Chemical Aids FAQs

Straight answers to the questions people ask most when choosing and using welding chemicals and consumable fluids.

What is anti-spatter and do I need it?icon-minus-redicon-plus-red

Anti-spatter is a spray, liquid or gel applied to the work and to the torch nozzle so that weld spatter does not stick. The spatter can then be wiped or brushed off rather than ground off, which saves cleaning time and protects the surface. It is most useful for MIG and flux-cored welding, which produce a lot of spatter.

It comes as aerosols, pump sprays and larger refills, in water-based and solvent-based types. Water-based types generally give off fewer solvent fumes and are less flammable, but check the label and safety data sheet. Apply a thin film only, and keep it away from the joint itself.

Why would I need a silicone-free anti-spatter?icon-minus-redicon-plus-red

Silicone is an ingredient in some anti-spatter products. It can stay on the surface and stop paint, powder coating, plating or adhesives from sticking properly, causing defects such as craters or poor adhesion. If the work will be painted, coated, bonded or plated afterwards, use a silicone-free product and clean the parts as the finish requires.

Some workshops and paint shops ban silicone altogether to protect their finishing lines. Check the product label, as not every anti-spatter is silicone-free.

How do I choose the right coolant for a water-cooled torch or cooler?icon-minus-redicon-plus-red

Use the coolant that the machine or cooler maker specifies. The coolant protects against freezing and corrosion, helps stop algae growing, and must be suitable for the pump, hoses and torch materials. Some systems need a low-conductivity coolant for electrical reasons, and some coolers are designed around a particular mix.

The right choice also depends on how cold your workshop gets, since coolants are rated for the lowest temperature they protect to. Do not use plain tap water as a long-term substitute, and do not mix different coolants unless the makers say it is fine, because they may react or cloud. If in doubt, check the manual or ask the maker.

Which cleaners and degreasers can I use before welding?icon-minus-redicon-plus-red

Use a cleaner made for metal preparation that evaporates fully and leaves no residue. Oil, grease, cutting fluid and marker pen cause porosity and poor welds, and stainless steel and aluminium are especially sensitive. Wipe with a clean cloth and let the surface dry fully before welding.

An important safety point: vapour from some chlorinated solvents can break down in the heat and ultraviolet light of an arc into toxic gases. Never weld where the vapour of such solvents is present, and make sure the solvent has fully evaporated and the area is ventilated. Read the label and the safety data sheet before use.

How does dye penetrant testing work?icon-minus-redicon-plus-red

Penetrant testing finds cracks and other flaws that reach the surface of a weld or part. Three products are used: a cleaner, a penetrant (often a coloured dye) and a developer. You clean the surface, apply the penetrant and leave it to soak for the time the instructions give, remove the excess, then spray the developer, which draws penetrant out of any flaw and shows it as a mark.

It only shows flaws that are open to the surface, not those inside the metal. Use products from the same system together, work in a ventilated area, and follow the instructions on timings and cleaning.

Can I use oil or grease on welding and gas equipment?icon-minus-redicon-plus-red

Not on oxygen equipment. Oil and grease can ignite violently in contact with pure oxygen, so never lubricate oxygen regulators, valves, hoses or fittings, and keep them clean, including from oily hands and gloves. Where a lubricant is genuinely needed, use only one that the equipment maker states is suitable for oxygen use.

Away from oxygen equipment, lubricants and penetrating oils are fine for tools, hinges, seized fasteners and moving parts. Cutting and tapping fluids make drilling and tapping easier and help tools last. Keep all oils away from the weld area and wipe them off before welding.