WE HAVE SOME GREAT LIMITED-TIME OFFERS - CLICK HERE TO VIEW THEM WE SHIP WORLDWIDE    /    All UK ORDERS GREATER THAN £75 EX VAT DELIVERED FREE    /    WE SHIP WORLDWIDE    /    ALL EUROPEAN ORDERS GREATER THAN £500.00 ex VAT DELIVERED FREE    /    WE SHIP WORLDWIDE

GBC Pipe Saws & Flame Cutting Machines

GBC-Logo

With over 35 years of experience under its belt, GBC pride itself on the development and manufacturing of pipe saws & flame cutting machines to cater to customers’ needs and establishing themselves at the forefront of technological advancements in pipework.

Each machine is designed and constructed for different purposes. Choose from a selection of pipe saws & flame cutting machines. Options include different types and models and plate bevelling machines, ranging from compact portable models and heavy-duty sturdy units. Choices between a variety of pipe sizes to suit your needs.

GBC Pipe Saws & Flame Cutting Machines FAQs

Answers to common questions about choosing and using portable pipe saws and flame pipe cutting machines.

Should I choose a pipe saw or a flame cutting machine?icon-minus-redicon-plus-red

It mostly comes down to the material and the finish you need. Flame (oxy-fuel) cutting is suited to mild and low alloy steels and works by heat, so the cut edge will usually need some cleaning before welding. An orbital pipe saw is a cold-cutting method: a blade travels around the pipe, so there is no flame and no heat input from the cut itself. Saws are also used on stainless steel and some non-ferrous pipe.

Flame machines tend to suit heavier carbon steel pipe and plate, while saws are often chosen when a square, clean, weld-ready end matters. Check the outside diameter and wall thickness range of any machine against your pipe. Our team can help you choose.

Can I flame cut stainless steel pipe?icon-minus-redicon-plus-red

Not with an ordinary oxy-fuel set-up. The process relies on the steel burning in a jet of oxygen and the resulting oxide melting away. Stainless steel, cast iron and non-ferrous metals form oxides that do not clear in the same way, so standard flame cutting is not suitable for them unless special powder-assisted equipment is used.

For stainless pipe, a cold-cutting saw or another method recommended by the equipment maker is the usual choice. Always check what materials a machine is designed for in its manual before you buy or use it.

How does an orbital pipe saw work, and why is it used for weld preparation?icon-minus-redicon-plus-red

The pipe is clamped in a rigid vice and a circular blade is driven in a planetary path around it, feeding in as it goes. A small blade can therefore cut a large pipe. Because it is a cold cutting method, there is no heat-affected edge, and the end is normally square.

Some saws can cut and bevel in one pass, which gives a ready-to-weld end. Capacity is set by the outside diameter and wall thickness the vice and drive can handle, so always check both against the pipe you cut. Use clean jaws and blades when working on stainless steel to avoid contaminating it.

Which fuel gas should I use for flame cutting, acetylene or propane?icon-minus-redicon-plus-red

Acetylene gives the hottest, most concentrated flame, so it starts a cut faster and gives a narrower heat-affected zone. It suits short cuts and bevel cutting. Propane pierces more slowly and needs a higher proportion of oxygen, but once the cut is under way the cutting speed is comparable, and it is more forgiving of changes in torch height.

Your cutting machine, torch and nozzle must be designed for the gas you choose, so follow the maker's instructions and use the correct nozzle for the thickness being cut. The two gases need different regulators, hoses and fittings and must never be interchanged.

Why is my flame cut rough, with drag lines and slag on the underside?icon-minus-redicon-plus-red

Cut quality problems usually come from a few settings. Travelling too fast leaves coarse, slanted drag lines and slag stuck to the bottom edge because the oxygen jet does not reach through the full thickness. A nozzle held too far from the work gives an uneven surface and a melted top edge. Too much cutting oxygen can cause gouging and extra slag, while too little leaves slag that is hard to clear. Too much preheat flame melts the top edge.

Try a test cut on scrap, adjust the speed first, and check that the nozzle is clean, undamaged and the right size. The maker's cutting chart gives starting settings.

What bevel angle should I cut on pipe for butt welding?icon-minus-redicon-plus-red

The angle is set by the welding procedure or drawing, not by the cutting machine. A common starting point for pipe butt joints is a bevel of about 30 degrees on each pipe end, giving an included angle of about 60 degrees, with a small root face and a root gap that the procedure specifies. Some procedures and codes use other angles, such as 37.5 degrees per side, so do not assume one figure suits every job.

A smaller angle uses less weld metal but gives less access to the root, which raises the risk of lack of fusion. Machine cutting or machining holds the angle, root face and fit-up more accurately than hand flame cutting.

Always follow your approved welding procedure or drawing for the exact angle, root face and gap.