WE HAVE SOME GREAT LIMITED-TIME OFFERS - CLICK HERE TO VIEW THEM WE SHIP WORLDWIDE    /    All UK ORDERS GREATER THAN £75 EX VAT DELIVERED FREE    /    WE SHIP WORLDWIDE    /    ALL EUROPEAN ORDERS GREATER THAN £500.00 ex VAT DELIVERED FREE    /    WE SHIP WORLDWIDE

GF 6 Pipe Cutting Machines

The new GF series sets new standards in orbital pipe machining. Numerous innovative functions combined with an ergonomic design create significant advantages for you in the industrial prefabrication of pipeline systems.

GF AVM

Pipe Cutting and bevelling machine with automatic feed module AVM. The intelligent AVM controls the feed and the cutting process is automated. Cutting and bevelling high-alloy steel (stainless steel), low and unalloyed steel, plastics, casting materials and non-ferrous metals in just seconds using the "Planetary Cutting" method.

GF MVM 

Pipe cutting and bevelling machine with manual feed version MVM. With the help of a hand wheel, the machine head rotates easily around the pipe with a constant speed.

GF Pipe Cutting Machines FAQs

Practical answers on choosing, setting up and using orbital pipe cutting and bevelling machines that carry a small circular saw blade round the pipe.

Will cutting with an orbital saw machine leave heat marks on stainless steel pipe?icon-minus-redicon-plus-red

Normally not. These machines use a cold, mechanical cutting process: a small circular saw blade plunges into the pipe and is driven round it, so the pipe is not heated the way it would be by a flame or plasma cutter. That matters on stainless steel, where heat tint and a heat-affected zone can reduce corrosion resistance.

The cold process only holds if the cut is done properly. A worn blade, the wrong blade for the material, too much feed or a lack of lubricant can still create heat, so use the blade, speed and lubricant recommended in the manufacturer's manual.

Which materials can this type of machine cut, and do I change the settings for each?icon-minus-redicon-plus-red

Machines of this type are made to cut and bevel stainless and other high-alloy steels, low-alloy and plain steels, cast materials, non-ferrous metals such as aluminium, copper and brass, and many plastic pipes. Most have an electronic variable speed control so the blade speed can be matched to the material.

In general, tougher alloys call for a slower blade speed and a blade made for that material, while softer metals and plastics need their own care to avoid clogging or melting. Do not guess: the manual and the blade maker's chart give the speed and blade for each material, and the data plate shows what your machine can handle.

Why does the wall thickness a machine can cut depend on the material?icon-minus-redicon-plus-red

Harder, tougher materials need more cutting force and heat the blade more, so a machine that copes with a given wall in mild steel may only manage a thinner wall in a high-alloy steel. For that reason makers usually quote the wall thickness range as depending on the material.

Makers also note that a thicker wall can sometimes be cut by using a manual feed or by making the cut in more than one pass, depending on the blade diameter. Treat that as something to check, not assume: look up your pipe diameter, wall thickness and material against the machine's application table in the manual before you start.

Can I cut short lengths of pipe or elbows with one of these machines?icon-minus-redicon-plus-red

Some machines can, but it depends on the design. Certain models have clamping jaws that can be set in a second position so a shorter length of pipe can be held and cut, and some have a second blade position or a motor handle shaped so that an elbow can be cut off.

Check the manufacturer's data sheet for your machine before buying or planning the job, because this is not a feature of every machine. For short lengths, make sure the pipe is gripped firmly by the clamping jaws and cannot move or rotate, since a loose short piece is a common cause of poor cuts.

Can the clamping jaws damage or contaminate stainless steel pipe?icon-minus-redicon-plus-red

They can if the wrong ones are used. Iron picked up from steel or cast iron tooling can be left on the surface of stainless steel, where it may rust later and make the pipe look as if it is corroding. For this reason makers supply stainless steel clamping attachments for use on stainless pipe, to protect against contact corrosion.

Fit the stainless attachments before clamping stainless pipe, keep them clean, and do not use them on carbon steel and then on stainless without cleaning them first. Where the machine is shared between materials, a thorough clean before stainless work is good practice.

How do I mark and line up the cut position accurately?icon-minus-redicon-plus-red

Many machines include a line laser that projects a line across the pipe to show exactly where the blade will cut. Mark the pipe at the position you want, bring the laser line onto the mark, then clamp the pipe so it cannot slip.

Allow for the thickness of the blade, and for any material that will be removed by a bevel, when you measure the length you need. Do not look into a laser beam, keep the lens clean, and follow the manual for fitting and aligning the laser, as the method differs between machines.