WE HAVE SOME GREAT LIMITED-TIME OFFERS - CLICK HERE TO VIEW THEM WE SHIP WORLDWIDE    /    All UK ORDERS GREATER THAN £75 EX VAT DELIVERED FREE    /    WE SHIP WORLDWIDE    /    ALL EUROPEAN ORDERS GREATER THAN £500.00 ex VAT DELIVERED FREE    /    WE SHIP WORLDWIDE

HMT Drill Taps

HMT Drill Taps FAQs

Answers to common questions about combination drill-taps that drill and thread a hole in a single operation.

What is a combination drill-tap and what does it do?icon-minus-redicon-plus-red

A combination drill-tap is a single tool with a drill point at the front and a tap section behind it. It drills the hole, usually forms a small lead-in chamfer, and then cuts the thread, all in one pass without changing tools.

Because the hole and the thread are cut by the same tool in the same setup, they stay in line with each other. The drill diameter is chosen to suit the thread size, so you do not need to look up a separate tap drill for each job. It is mainly used where a lot of threaded holes are needed quickly, such as fabrication and maintenance work.

Why do I need cutting fluid when using a drill-tap?icon-minus-redicon-plus-red

Tapping is a high-friction cut because the tap flanks are in contact with the work along the whole thread. Without proper lubrication, friction and heat build up, the tool wears faster and the thread finish suffers, and the risk of the tool seizing and breaking goes up.

A purpose-made cutting or tapping fluid is usually the better choice, and tougher materials such as stainless and alloy steels generally need more lubrication than aluminium or cast iron. Apply it before you start and keep topping it up, especially in deeper holes where fluid struggles to reach the cutting edges.

Why do drill-taps break and how can I avoid it?icon-minus-redicon-plus-red

Most breakages come from the torque rising faster than the tool can take. Common causes are chips packing in the flutes, poor alignment, too little lubrication, running too fast, a worn tool, and the tap running out of depth in a blind hole.

To reduce the risk, keep the tool square to the surface, use plenty of suitable fluid, let the tool cut at a steady controlled speed, and back out briefly to clear chips if it starts to bind. Use a torque-limiting clutch or setting where your equipment has one, and replace worn tools before they start to struggle. If a tool breaks repeatedly, check the setup and the lubrication before blaming the tool.

Can I use a drill-tap in a blind hole?icon-minus-redicon-plus-red

It depends on the design, so check the maker's instructions for your tool. Some combination tools are specifically recommended for through holes only, because the chips have nowhere to go at the bottom of a blind hole.

If a blind hole is unavoidable, remember that the drill point and the unthreaded lead-in reduce the useful thread depth, and chips build up at the bottom and reduce it further. Allow extra depth beyond the thread you need, clear swarf regularly, and never drive the tool into the bottom of the hole, because that is a common way to break it. For deep blind holes, a separate drill and a spiral-flute tap are often the safer approach.

Does the drill-tap need different speed and feed for drilling and tapping?icon-minus-redicon-plus-red

A drill-tap does two jobs in one pass, so follow the maker's instructions for speed and feed. The general principle is that the drill section should break through the workpiece before the tap section starts to cut, so do not stop or force the tool while the threaded part is entering the hole.

In practice use a slow, steady, controlled rotation and a feed that lets the tool cut rather than rub. Exact figures depend on the tool, the material, the machine and the thread size, so use the data supplied with the tool rather than a general figure.

How do I choose the right thread size and type?icon-minus-redicon-plus-red

Choose the thread to match the bolt, stud or fitting that will go into it. That means matching both the diameter and the pitch, and also the thread form: metric, UNC (unified coarse inch) and BSW (Whitworth) are not interchangeable even when the sizes look close.

Metric pitch is given in millimetres, while inch threads are given as threads per inch. A pitch gauge and calipers on the mating male thread will tell you what you have. A quick check is that a correct bolt should start by hand for several turns; if it does not, it is the wrong thread. Do not force a mismatched thread, as that risks cross-threading and a weak joint.