The website is working fine. Please feel free to place orders. WE SHIP WORLDWIDE    /    All UK ORDERS GREATER THAN £75 EX VAT DELIVERED FREE    /    WE SHIP WORLDWIDE    /    ALL EUROPEAN ORDERS GREATER THAN £500.00 ex VAT DELIVERED FREE    /    WE SHIP WORLDWIDE
    Share this page on Facebook   Share this page on LinkedIn   Share this page on Twitter   Share this page on Whatsapp   

    Rapid Ref : 501020-3SET  

    HMT ImpactaMag Reamer Set: 14, 18, 22mm
    501020-3SET

    £217.92  EX VAT
    SSP Suggested Selling Price = £256.38  YOU SAVE £38.46
     Buy in 3 easy interest free payments of £72.64† with

    The HMT ImpactaMag HSS reamer is a unique double-use reamer for enlarging and aligning holes in metals and hard materials, with a specially designed cutting geometry that is designed to allow the tool to be used in an Impact wrench or a Magnet drill. When used in an Impact wrench, it is secured into a special adaptor, meaning the tool is easier to control, apply the correct feed rate, and withdraw from the finished hole, enhancing tool life. This reamer will also fit into a standard Weldon magnet drill arbor, providing a versatile '2 in 1' solution for circumstances where it may be more appropriate to use a magnet drill.

    It is ideal for steel erectors and bridge work. Used for Network Rail bridge refurbishment and strengthening. It is ideal for modifying and enlarging holes ready to install TCB bolts and friction grip bolts.

    • ImpactaMag reamers are secured directly to the impact wrench
    • ImpactaMag reamers can also be used with any standard Magnet Drill
    • ImpactaMag reamers are now available in intermediate sizes

    UNIQUE 6 flute design for a faster, smoother cut. For a 1/2" Drive Impact Wrench, use 00200-12A-19 HMT ImpactaMag Adaptor. For 3/4" Drive Impact Wrench use 00200-34A-19 HMT ImpactaMag Adaptor.

    Product Details

    Brochures & Manuals

    HMT Reamers FAQs

    Answers to common questions about choosing and using reamers for enlarging and aligning holes in steelwork.

    What is a reamer used for on steelwork?icon-minus-redicon-plus-red

    A reamer enlarges and cleans up an existing hole to a more accurate size and a smoother finish. In structural steelwork it is commonly used during erection, when plates or sections have been bolted loosely together and the holes do not quite line up, so that a bolt can pass through without damaging its thread.

    The result is a slightly larger or elongated hole, so it is a tool for small, local misalignment rather than a general way to make holes. Check the connection requirements for your job before reaming.

    Can a reamer fix a hole that is in the wrong place?icon-minus-redicon-plus-red

    No. A reamer follows the hole that is already there, so it will not correct a hole that is off position or not straight. It can deal with small, local misalignment between plies, but only by removing the minimum material needed.

    If holes are badly out, reaming is the wrong answer and the connection may need to be reviewed by the person responsible for the design. Do not try to fill mislocated holes by welding without that advice.

    Do I need cutting fluid when reaming?icon-minus-redicon-plus-red

    In most cases, yes. Cutting fluid lubricates the cut, cools the tool, helps clear chips and generally gives a better finish and longer tool life. Reaming dry can leave a rougher hole and may give an oversize one.

    The type of fluid can affect both finish and final hole size, and the effect varies with the fluid, the material and the reamer. Use the fluid the reamer maker recommends for your material, and where the size is critical, try it on a test piece and measure the result before reaming the job.

    Why does my reamer chatter and how do I stop it?icon-minus-redicon-plus-red

    Chatter spoils the hole finish and damages the reamer. Common causes are a loose workpiece, play in the tool or tool holder, too much overhang, and the wrong speed or feed pressure.

    Clamp the work firmly, keep the reamer square to the hole and well supported, and avoid forcing it. If chatter continues, check the speed and feed against the maker's guidance, and make sure the hole you started with is straight and not badly off-centre.

    Shop Similar Categories