The website is working fine. Please feel free to place orders. WE SHIP WORLDWIDE    /    All UK ORDERS GREATER THAN £75 EX VAT DELIVERED FREE    /    WE SHIP WORLDWIDE    /    ALL EUROPEAN ORDERS GREATER THAN £500.00 ex VAT DELIVERED FREE    /    WE SHIP WORLDWIDE

Harris Machine Torches

Harris Machine Torches FAQs

Straight answers on choosing, setting up and looking after machine-mounted oxy-fuel cutting torches, with the safety points that matter most.

What is a machine cutting torch and how does it differ from a hand torch?icon-minus-redicon-plus-red

A machine cutting torch is a barrel-style torch that is clamped into a carriage, profile cutter, pipe-cutting rig or similar mechanised equipment instead of being held by an operator. The machine moves the torch at a steady speed along the line of cut, which is why it is used for long straight cuts, repeat shapes and bevels where an even, repeatable edge matters.

The cutting process is the same as with a hand torch: a preheat flame brings the steel up to temperature and a jet of cutting oxygen burns through it. The differences are mostly in the build, such as a longer barrel to reach the work, a mounting point for the machine, and often a rack for height adjustment. Check the machine's mounting diameter before choosing.

What do two-hose and three-hose machine torches mean?icon-minus-redicon-plus-red

This usually describes how many gas hoses connect to the torch. A two-hose torch is normally fed with oxygen and fuel gas, and the preheat gases are mixed inside the torch before they reach the tip. A three-hose torch usually has separate connections for cutting oxygen, preheat oxygen and fuel gas, so the preheat oxygen and cutting oxygen can be set independently and the gases are often mixed at or near the nozzle.

The exact arrangement varies with the design, so do not assume. The right choice depends on the fuel gas, the tips you plan to use and what your machine's gas controls can supply. Always follow the torch maker's instructions for hose connections, and check the tip type matches the torch type.

What is the rack on a machine torch for?icon-minus-redicon-plus-red

A rack is a toothed bar on the barrel that engages a pinion in the machine's torch holder, so that the torch can be raised or lowered by turning a knob. This lets you set the distance between the nozzle and the plate without loosening the clamp and without disturbing the angle of the torch.

It is useful because nozzle height has a direct effect on cut quality: the preheat flame needs to be at the right distance from the plate for the cut to start cleanly and stay square. Torches without a rack are normally positioned by sliding them in the clamp, which is harder to adjust finely. Make sure the rack and the holder are compatible and that the clamp is tight before cutting.

How do I choose the right cutting tip for the thickness of steel?icon-minus-redicon-plus-red

Tips are chosen mainly by the thickness of the material to be cut and by the fuel gas being used. The cutting oxygen bore is sized to suit the thickness, so a thicker plate needs a larger bore and more cutting oxygen. The tip type also depends on the fuel gas, on whether the work is manual or mechanised, and on the torch design, so a tip made for acetylene is not automatically right for propane.

Standard tips have a parallel central bore with preheat ports around it, while high-speed tips are mainly used on mechanised equipment to exploit higher travel speeds. Use the tip chart from the torch or tip maker to match thickness, tip size and gas pressures, and do not guess.

Should I use acetylene or propane for machine cutting?icon-minus-redicon-plus-red

Both work, and the choice depends on the job. Acetylene gives the hottest flame, so it starts a cut and pierces plate faster, and its focused flame suits thin plate and bevel cutting with little distortion. Propane has a lower flame temperature and is slower to pierce, but cutting speeds with comparable tips are similar, it often gives a smoother edge with less slag, and it tolerates more variation in nozzle height.

The tip must be designed for the fuel gas you use, and the torch, hoses, regulators and arrestors must all be suitable for that gas. Ask your gas supplier or our team if you are unsure which suits your cutting thickness and equipment.

Why is the top edge of my cut rounded or covered in slag?icon-minus-redicon-plus-red

Common causes are too much preheat flame, a nozzle held too high, travel that is too fast or too slow, too much or too little cutting oxygen, and a dirty or damaged tip. Too much preheat tends to melt and round the top edge and adds slag. Travelling too fast leaves coarse drag lines and slag on the bottom edge. Too low a cutting oxygen flow gives poor slag removal.

Work through the list one setting at a time: confirm the tip is clean and the right size for the thickness, set the nozzle height, reduce the preheat to the recommended setting, then adjust travel speed using the maker's chart. Make test cuts on offcuts before running a job.