WE HAVE SOME GREAT LIMITED-TIME OFFERS - CLICK HERE TO VIEW THEM WE SHIP WORLDWIDE    /    All UK ORDERS GREATER THAN £75 EX VAT DELIVERED FREE    /    WE SHIP WORLDWIDE    /    ALL EUROPEAN ORDERS GREATER THAN £500.00 ex VAT DELIVERED FREE    /    WE SHIP WORLDWIDE

Magnetic Tools

Magnetic Tools FAQs

Straight answers to the questions people ask most when choosing and using magnetic squares, holders and levels.

What are magnetic tools used for in welding and fabrication?icon-minus-redicon-plus-red

Magnetic squares, positioners and holders hold pieces of steel at a set angle, usually 90, 45 or 60 degrees, so you can tack them without needing a spare pair of hands. They save time and give repeatable joints in frames, brackets, boxes and structural work. Other magnetic tools include levels that grip steel or pipe, and flexible holders that position small parts, cables or lamps.

They are positioning aids rather than structural clamps. Their job is to hold the work in the right place for tacking, after which the tacks hold it.

What does the force rating on a magnet mean?icon-minus-redicon-plus-red

The force figure is the pull the magnet gives on a thick, clean, flat piece of mild steel under ideal conditions, normally measured pulling straight off. In real use the holding force is lower, and it is not a safe working load. It drops with thin, painted, rusty, curved or rough surfaces, with any air gap, and with some grades of steel, and it is weaker against sideways loads than a straight pull.

Use the figure to compare tools rather than to decide how much a magnet can safely carry. A higher figure usually means a bigger, heavier magnet. Never use a magnetic tool to support something that could fall and hurt someone.

What is the difference between a switchable magnet and a permanent magnet?icon-minus-redicon-plus-red

A permanent magnet is always on, so it grips whenever it touches steel and needs a firm pull to detach it. A switchable (on/off) magnet has a mechanism, usually a lever or dial, that turns the magnetic force on and off. Switching it off makes it easier to position, to release from the work and to clear of swarf, and it is kinder to fingers because it does not snap onto the steel.

Switchable models are usually the better option for frequent use and for stronger magnets. Some squares have a separate switch for each face, so you can place one part and then the other.

Which angles do I need on a magnetic square?icon-minus-redicon-plus-red

A 90 degree square suits box frames, T-joints and corners. 45 degrees gives mitred corners, and many squares offer 30, 45, 60 and 90 degrees in one body. 60 and 120 degrees suit hexagonal and triangular frameworks. Adjustable squares let you set other angles, which is useful for odd-angled brackets and bracing.

Choose a type that covers the angles you meet most. Fixed-angle tools are simple and quick, while adjustable ones are more flexible but you should check the setting is locked, and use a protractor or gauge when the angle must be exact.

Will magnetic tools grip every metal and surface?icon-minus-redicon-plus-red

Magnets only grip ferromagnetic metals. Ordinary mild steel and cast iron are fine. Aluminium, copper and brass are not magnetic. Stainless steels vary: some grades grip a magnet and others grip weakly or not at all, and forming or working the metal can change this. Do not judge a grade by whether a magnet sticks.

Paint, rust, scale, spatter, swarf and a rough or curved surface all create a gap between magnet and metal and cut the grip. Thin material also holds less magnetic force. Clean the surface and test the grip before relying on it, and use mechanical clamps on non-magnetic metals.

Can a magnet affect my welding arc or be damaged by heat?icon-minus-redicon-plus-red

Yes to both. Strong magnets can disturb the welding arc, making it wander or blow to one side, a problem known as arc blow. It is most noticeable with DC welding and near the ends of a joint. Keep magnetic tools as far from the weld as practical, or remove them before the main weld.

Heat also damages magnets. Many permanent magnets lose strength if they get hot, and some lose it permanently, so do not leave them against hot metal or in the line of spatter. Check the maker's temperature limit. Spatter on the faces can also spoil the flat surface and weaken the grip.