Straight answers to the questions people ask when choosing and looking after the tungstens, cups, collets and small spares for a compact micro TIG torch.
What is a micro TIG torch and what is it used for?

A micro TIG torch is a miniature air-cooled or water-cooled torch with a very small head and a slim handle. It is made for precision work on thin metal, small components and awkward positions where a full-size torch will not fit or is too heavy to control.
Typical uses include aerospace and instrument work, artistic metalwork and very thin sheet. Because the head is small, the torch is rated for a lower maximum current than a full-size torch, so check the rating on the torch before you plan the job. The small spares for it (cups, collets, bushings and short tungstens) are different sizes from full-size parts, so do not assume they swap.
What tungsten diameter should I use in a micro torch?

As a rule, the lower the current, the smaller the tungsten diameter and tip angle. A tungsten that is too large for the current can give an unstable arc and hard starting, while one that is too small will overheat and erode at higher current.
For very thin material and low current, the finer diameters that micro torches are designed for are usually the right choice. Move up a size as the thickness and current rise, and keep within the current range the electrode maker gives for that diameter. The torch collet and collet body must match the tungsten diameter, so choose the electrode size first and then the matching small parts.
Which type of tungsten is best for a micro torch: ceriated, lanthanated or thoriated?

For low-current work, ceriated (grey) and lanthanated (black, gold or blue) tungstens are the usual choices. Both suit DC and can also be used on AC, and both are commonly chosen for easy arc starting and good stability at lower current. Technical sources list ceriated for the lower to mid current range.
Thoriated tungsten (red, and other thoria colours) is slightly radioactive. Technical guidance advises weighing whether it is justified and notes that lanthanum or cerium oxides can replace it with lower risk. Pure and zirconiated tungstens are mainly for AC work on aluminium. Check the colour band or marking on the electrode, and the maker's guidance, before use.
How should I sharpen tungsten for a micro torch?

For thin material and low current, grind the tungsten to a fine point. A small, intense arc from a pointed electrode suits thin sheet, and the lower the current the smaller the tip angle should be. Some sources recommend a very small flat on the end of the point; the right angle and flat depend on the current and the maker's guidance.
Grind lengthwise, along the electrode, not around it, so the grind marks run towards the tip. Circular marks can make the arc wander. Use a grinding wheel kept only for tungsten so the point does not pick up contamination, and re-grind to the same shape each time for repeatable results.
What should I do if my tungsten touches the weld pool?

Stop and re-grind it. Touching the pool, or touching the filler rod to the electrode, contaminates the tip. A contaminated tungsten typically gives a wandering, unsteady arc, can cause porosity, and can leave tungsten inclusions in the weld.
Break or cut off the contaminated end, then re-sharpen the tungsten properly before you continue. If the contamination is severe, fit a new electrode. Hotter pools tend to contaminate the tungsten faster, so keep a steady arc length and a steady hand, and keep spare short tungstens to hand. Using a tungsten with a damaged tip will only make the starting and arc problems worse.
Should I use a clear glass cup or a ceramic cup on a micro torch?

A clear borosilicate glass cup lets you see the tungsten and the pool, which helps in corners and tight spaces. It is a good choice for small, close-up work and for learning, because you can see where the electrode is.
The trade-offs are that glass is brittle and does not suit being dragged or walked across rough surfaces, and it can cloud with fume deposits over time. A ceramic (alumina) cup is the tougher option and is usually what comes fitted to a torch. Replace any cup that is cracked, chipped or badly clouded, and choose the cup that is made for your torch style, as cups are not interchangeable between torch types.