WE HAVE SOME GREAT LIMITED-TIME OFFERS - CLICK HERE TO VIEW THEM WE SHIP WORLDWIDE    /    All UK ORDERS GREATER THAN £75 EX VAT DELIVERED FREE    /    WE SHIP WORLDWIDE    /    ALL EUROPEAN ORDERS GREATER THAN £500.00 ex VAT DELIVERED FREE    /    WE SHIP WORLDWIDE
    Share this page on Facebook   Share this page on LinkedIn   Share this page on Twitter   Share this page on Whatsapp   

    Rapid Ref : 790085380  

    Orbitalum Cutting Head 30° for BRB2 Kit 1, V-/Y- Prep, ID min - OD max 14.5 - 48mm
    790085380

    £650.00  EX VAT
     Buy in 3 easy interest free payments of £216.67† with

    Orbitalum Heavy Duty Cutting Head 30° for BRB2 Kit 1, V-/Y- Prep, ID min - OD max 14.5 - 48mm.

    Optimised work, smoother and steadier cutting. The bevel heads can be replaced like a tool mounting plate.

    Bevel Head comes with:

    • 3 multifunctional tools, tool no MFW12-V / I-2
    • 1 multifunctional tool, tool no MFW5-V / I-2
    • 3 torx screws
    • 3 fastening screws M5 x 16

    Orbitalum Cutting Heads for BRB 2 / BRB 4 FAQs

    Bevel cutting heads for compact boiler-pipe preparation machines: what they do, how to choose one and how to look after it.

    What does a bevel cutting head do?icon-minus-redicon-plus-red

    A bevel cutting head fits on a compact pipe-end preparation machine and machines the end of a tube to a set weld angle, usually a V-prep. The machine holds itself inside the tube and the head turns round the tube end, so the bevel is cut square and can be repeated from one tube to the next.

    The head replaces the plain tool plate on the machine, so the same machine can be set up for different jobs. Makers describe these machines as designed for boiler, tank and heat-exchanger work where there is little room between tubes. Always follow the manual for your machine when fitting a head.

    How does the machine hold the tube while the head cuts?icon-minus-redicon-plus-red

    These machines usually clamp on the inside diameter of the tube. A mandrel goes into the bore and clamping wedges expand against the inside wall, which centres the machine on the tube so the bevel is concentric with the bore.

    Some machines use clamping wedges fixed to the mandrel so loose parts cannot fall into the tube, which matters on vertical work or in a tank. Others have pneumatic clamping that centres and clamps at the flick of a switch. The right mandrel and wedge set depends on the tube bore, so check the data plate and manual for your machine.

    How do I choose the bevel angle?icon-minus-redicon-plus-red

    Choose the angle that your welding procedure specification calls for. Cutting heads are normally made in a few standard angles, with 30, 37.5 and 45 degrees the common choices, and the angle is fixed by the head, so you need to buy the one that matches.

    The angle, together with the root face and gap, sets the included angle of the joint, which controls how well the torch or electrode can reach the root. A wider angle gives better access but needs more weld metal. If you are not sure, ask whoever wrote the procedure or the welding coordinator before ordering.

    What wall thickness and tube materials can a cutting head handle?icon-minus-redicon-plus-red

    The maximum wall thickness depends on the head, the machine and the material. Makers state that the limits depend on the tube material and size, and the limit for stainless steel is usually lower than for carbon steel or aluminium.

    The tools are normally suited to unalloyed, low-alloy and high-alloy steels, but check the maker's data for the specific head. Do not force a heavier cut than the machine and head are rated for. Take the cut in stages if the manual allows, and keep within the wall thickness shown on the head's data sheet.

    Shop Similar Categories