WE HAVE SOME GREAT LIMITED-TIME OFFERS - CLICK HERE TO VIEW THEM WE SHIP WORLDWIDE    /    All UK ORDERS GREATER THAN £75 EX VAT DELIVERED FREE    /    WE SHIP WORLDWIDE    /    ALL EUROPEAN ORDERS GREATER THAN £500.00 ex VAT DELIVERED FREE    /    WE SHIP WORLDWIDE

Orbitalum Cutting Heads for BRB 2 / BRB 4

Orbitalum Cutting Heads for BRB 2 / BRB 4 FAQs

Bevel cutting heads for compact boiler-pipe preparation machines: what they do, how to choose one and how to look after it.

What does a bevel cutting head do?icon-minus-redicon-plus-red

A bevel cutting head fits on a compact pipe-end preparation machine and machines the end of a tube to a set weld angle, usually a V-prep. The machine holds itself inside the tube and the head turns round the tube end, so the bevel is cut square and can be repeated from one tube to the next.

The head replaces the plain tool plate on the machine, so the same machine can be set up for different jobs. Makers describe these machines as designed for boiler, tank and heat-exchanger work where there is little room between tubes. Always follow the manual for your machine when fitting a head.

How does the machine hold the tube while the head cuts?icon-minus-redicon-plus-red

These machines usually clamp on the inside diameter of the tube. A mandrel goes into the bore and clamping wedges expand against the inside wall, which centres the machine on the tube so the bevel is concentric with the bore.

Some machines use clamping wedges fixed to the mandrel so loose parts cannot fall into the tube, which matters on vertical work or in a tank. Others have pneumatic clamping that centres and clamps at the flick of a switch. The right mandrel and wedge set depends on the tube bore, so check the data plate and manual for your machine.

How do I choose the bevel angle?icon-minus-redicon-plus-red

Choose the angle that your welding procedure specification calls for. Cutting heads are normally made in a few standard angles, with 30, 37.5 and 45 degrees the common choices, and the angle is fixed by the head, so you need to buy the one that matches.

The angle, together with the root face and gap, sets the included angle of the joint, which controls how well the torch or electrode can reach the root. A wider angle gives better access but needs more weld metal. If you are not sure, ask whoever wrote the procedure or the welding coordinator before ordering.

How do I know which head fits my machine and tube size?icon-minus-redicon-plus-red

Heads are made for a particular machine size and cover a stated range of tube sizes, usually given as a minimum inside diameter and a maximum outside diameter, sometimes in fixed steps. Check three things: that the head is designed for your machine, that your tube bore and outside diameter fall inside the stated range, and that the wall thickness is within the head's limit.

The machine data plate and operating instructions list which heads and mandrel sets suit it. Our team can help you match a head to the machine if you have the model details to hand.

What wall thickness and tube materials can a cutting head handle?icon-minus-redicon-plus-red

The maximum wall thickness depends on the head, the machine and the material. Makers state that the limits depend on the tube material and size, and the limit for stainless steel is usually lower than for carbon steel or aluminium.

The tools are normally suited to unalloyed, low-alloy and high-alloy steels, but check the maker's data for the specific head. Do not force a heavier cut than the machine and head are rated for. Take the cut in stages if the manual allows, and keep within the wall thickness shown on the head's data sheet.

What should I do before fitting or changing a cutting head?icon-minus-redicon-plus-red

Make the machine safe first. Before fitting a head, changing cutting bits or adjusting the clamping, disconnect the electric plug or shut off and disconnect the compressed air, and let the machine stop completely. The HSE says plant must be made safe before maintenance starts and that the work should only be done by competent people.

The maker's manual for this type of machine warns of flying chips and sharp edges and calls for safety goggles, cut-resistant gloves and safety shoes. It also warns that noise can exceed 80 dB(A), so wear hearing protection. Keep hands clear of the cutting bits and read the operating instructions before first use.