The website is working fine. Please feel free to place orders. WE SHIP WORLDWIDE    /    All UK ORDERS GREATER THAN £75 EX VAT DELIVERED FREE    /    WE SHIP WORLDWIDE    /    ALL EUROPEAN ORDERS GREATER THAN £500.00 ex VAT DELIVERED FREE    /    WE SHIP WORLDWIDE
    Share this page on Facebook   Share this page on LinkedIn   Share this page on Twitter   Share this page on Whatsapp   

    Rapid Ref : PB1  

    Pipe Buggy
    PB1

    £257.60  EX VAT
     Buy in 3 easy interest free payments of £85.87† with
    Please note, this product does not qualify for our standard shipping rates outside of the UK Mainland. Please contact us for shipping rates for this product.

    The Pipe Buggy provides a safe, easy way to move pipes around the workshop or site, helping prevent damage from dragging pipes along the ground.

    Weighing just 31.8 kg / 70 lbs, it is a lightweight yet durable solution for pipe handling. Its innovative handle and ratchet strap let the operator lift the pipe from the floor onto the buggy with minimal effort.

    Features

    • Maximum pipe diameter - 12"
    • Flat-free tyres
    • Ratchet hold down strap to secure pipe
    • Quick disconnecting handle for easy storage

    Brochures & Manuals

    BROCHURES & MANUALS
       View Brochure

    Material Handling FAQs

    Straight answers to the questions people ask most when choosing and using a cart or trolley for moving pipe and materials.

    How do I choose the right load capacity for a pipe cart?icon-minus-redicon-plus-red

    Work out the heaviest load you will realistically carry, including pipe, fittings and anything else on the bed, then choose a cart whose rated load is comfortably above it. The rating is normally marked on the cart or given in its instructions, so check the plate and the manual rather than assuming.

    Also check the rating of the wheels, the length and width of the bed against your longest pipe, and that the load will sit evenly. Under the work equipment regulations, equipment has to be suitable for the job it is used for, so a cart used beyond its rating is not suitable.

    How should I load pipe on a cart so it stays put?icon-minus-redicon-plus-red

    Place the pipe so the weight is spread evenly and kept low, with the heaviest pieces at the bottom and centred. Use any stops, side posts, chocks or cradles to stop pipe rolling, and secure the load with suitable straps or ties before moving off.

    Do not overload, do not stack pipe higher than the cart is designed to take, and keep the overhang of long pipe within what the maker allows. Release straps carefully, because loose pipe can roll. Always follow the cart manufacturer's loading instructions and your own risk assessment.

    Is it safe to push a heavily loaded cart by hand?icon-minus-redicon-plus-red

    It can be, but it needs thought. The law does not set a specific weight limit for manual handling; instead the HSE expects you to avoid hazardous handling where reasonably practicable and reduce the risk if you cannot. Pushing and pulling wheeled loads such as trolleys and carts are covered in the same way as lifting and carrying.

    A wheeled cart is usually far better than carrying pipe by hand, but think about the load, the route, slopes, the person pushing and whether a second person is needed. HSE publishes a simple assessment tool for pushing and pulling tasks.

    How do I look after a pipe cart and know when it needs attention?icon-minus-redicon-plus-red

    Check it before use for bent frames, cracks, loose fixings, damaged handles, worn or flat tyres and wheels that bind or wobble. Keep bearings and swivels clean and lubricate them as the maker advises, and keep tyre pressures right on air-filled wheels.

    Work equipment has to be kept in efficient working order and good repair, and inspected where it could deteriorate in a way that creates danger. How often you check depends on how hard and where the cart is used, so set it in your risk assessment. Take a damaged cart out of use until it is repaired.

    Shop Similar Categories