WE HAVE SOME GREAT LIMITED-TIME OFFERS - CLICK HERE TO VIEW THEM WE SHIP WORLDWIDE    /    All UK ORDERS GREATER THAN £75 EX VAT DELIVERED FREE    /    WE SHIP WORLDWIDE    /    ALL EUROPEAN ORDERS GREATER THAN £500.00 ex VAT DELIVERED FREE    /    WE SHIP WORLDWIDE

BRB 2 & BRB 4 with Std Clamp

BRB 2 & BRB 4 with Std Clamp FAQs

Answers to common questions about internally clamped boiler tube preparation machines, from choosing a clamp kit to safe use and care.

What does an internally clamped boiler tube preparation machine do?icon-minus-redicon-plus-red

It is a portable machine that grips the tube from the inside and then machines the tube end ready for welding. Clamps fit inside the bore and expand against a mandrel to centre and hold the machine, and a rotating head carries the cutting tools around the tube end.

Machines of this type can usually face the tube end square, cut the bevel and bore the inside edge in one set-up, depending on the tooling fitted. The data plate and manual give the tube size and wall thickness the machine is designed for.

Why is the bevel on a boiler tube important for the weld?icon-minus-redicon-plus-red

The bevel gives the welder access to the root of the joint so the first pass can fuse properly. Poor preparation is a recognised cause of incomplete root fusion: a root face that is too thick, a root gap that is too small, or a bevel angle that is too small can all stop the arc reaching the root.

The bevel angle, root face and root gap are normally set by the welding procedure for the job, so cut to that. A machined bevel is uniform all round the tube, which makes it easier to hold the correct gap than hand grinding does.

Why use a cold-cutting machine rather than thermal cutting?icon-minus-redicon-plus-red

A machine like this removes metal with cutting tools rather than heat. Thermal cutting creates a heat-affected zone, a band of metal beside the cut whose properties have changed, and these changes are usually undesirable because they can reduce toughness or corrosion resistance and increase the risk of cracking.

Mechanical preparation avoids that zone and leaves a clean, square face ready for welding. It also removes the oxidised edge that thermal cutting leaves, which would otherwise need grinding off. Follow the maker's advice for the material being cut.

How do I make the machine safe before changing tools or the clamp?icon-minus-redicon-plus-red

Stop the machine and make sure the moving parts have stopped, then isolate the power supply before you touch the tooling. For an air-driven machine that means shutting off and disconnecting the air, and releasing any stored pressure so nothing can move or cycle unexpectedly.

Most maintenance should be done with the power off, and the machine should be locked off if there is any chance it could be switched back on by someone else. Follow the maker's instructions, and make sure the person doing the work is competent to do it.

What protective equipment and clothing should I use when machining tube ends?icon-minus-redicon-plus-red

Your risk assessment decides, but it will normally include eye protection suited to flying chips and swarf, and hearing protection where the machine is noisy. The HSE explains that PPE must be assessed as suitable before use, maintained and stored properly, and that users need instruction and training in it.

Keep clothing close-fitting and hair tied back. Regulators warn that gloves can increase the risk of entanglement and are not acceptable near rotating parts, so do not wear loose gloves while the head is turning. Handle sharp swarf and freshly cut ends only when the machine has stopped.

Why does the machine chatter or leave a poor finish?icon-minus-redicon-plus-red

Chatter generally points to a lack of rigidity. Machining guidance from cutting tool makers lists a weak fixture or poor clamping, worn tools and cutting data that is too aggressive among the usual causes of vibration and poor surface finish.

Stop, re-seat and re-tighten the clamp, check the tool bits for wear or damage, and reduce the feed. Clean the inside of the tube so the clamp grips properly, and check the manual for the recommended settings for the material. A rough or noisy cut is a sign to stop and investigate, not to push on.