Gas lens front-end kits for small TIG torches: what they do, how to choose the cup and how to get the best shielding from them.
What is a gas saver kit and what does it do on a TIG torch?

A gas saver kit is a gas lens front end. It replaces the standard collet body and cup with a body that holds fine mesh screens, plus a matching cup, collet and usually the insulating parts that go with them. The screens smooth the argon into a steadier, more even column as it leaves the cup, instead of the more turbulent stream a standard collet body tends to produce.
The smoother flow gives better coverage of the weld pool and the hot tungsten, which helps most on vertical, corner, edge and curved work and on metals that react easily with air, such as stainless steel and titanium.
How is a gas lens different from a standard collet body?

Both hold the collet and tungsten and carry gas to the cup. The difference is the gas path. A standard collet body passes gas through a few ports, so the flow can swirl and may draw air into the shield. A gas lens passes it through mesh screens first, giving a calmer, more column-like flow.
That usually allows a longer tungsten extension and better coverage in awkward positions. A standard collet body is still perfectly adequate for a lot of general work in still air, and it works with the plain cups that normally come with the torch. A gas lens also needs a cup made to fit it, so the parts are bought as a matched set.
Will a gas saver kit really use less gas, and how do I set the flow?

Because the flow leaving the cup is smoother, a gas lens can often shield well at a lower flow than the same size cup on a standard collet body. In one training example a number 8 cup needed about 10 litres per minute with a standard body but about 5 with a gas lens. How much you save depends on the cup size, the job and draughts, so treat headline percentages as best-case figures.
There is no single exact rule for the setting, so start from the maker's guidance for your cup and torch, then reduce to the lowest flow that still gives clean, bright welds. Too much flow causes turbulence, can pull air in and can make the arc unstable. Flowmeters are not always accurate, so a flow tester is a useful check.
How far can I extend the tungsten with a gas lens?

Keep the tungsten extension as short as the joint allows. A gas lens holds its shield over a longer distance than a standard collet body, so more extension is possible, and larger cups allow longer extension still. Gas lens kit makers quote a maximum extension for ideal, draught-free conditions with argon, but treat any such figure as a best case and follow the instructions for your kit.
Extension that is too long lets air reach the weld pool and tungsten, and a torch maker's troubleshooting guide lists excessive electrode extension as a cause of tungsten inclusions. If you see porosity, discoloured welds or a dirty tungsten, shorten the extension or move up a cup size first.
Should I choose an alumina cup or a glass cup?

Alumina (ceramic) cups are the more durable choice and suit general work and a busy workshop. Glass (borosilicate) cups let you see through to the arc and the joint, which helps in inside corners, inside pipe and around tubing where a solid cup blocks the view.
The trade-off is that glass is more fragile and breaks more easily if the torch is dropped or knocked. Check the maker's guidance for the current each cup type can handle, and replace any cup that is cracked or chipped. Many welders keep both types and swap depending on the job.
How do I know which kit fits my torch?

Kits are made for a particular torch series or head style, so start by identifying your torch from the markings on the head, the handbook or the torch maker's parts list. The small-torch (2 series) kits are listed for the 9 and 20 style torches, and makers describe them as fitting most standard silicone-rubber-insulated torch bodies, so check the fit in the product description rather than assuming.
Then match the tungsten diameter, because the collet and gas lens adapter are sized to the electrode, and choose between standard, large diameter or stubby styles to suit your access and the cup you want. Our team can help you match a kit to your torch details.