WE HAVE SOME GREAT LIMITED-TIME OFFERS - CLICK HERE TO VIEW THEM WE SHIP WORLDWIDE    /    All UK ORDERS GREATER THAN £75 EX VAT DELIVERED FREE    /    WE SHIP WORLDWIDE    /    ALL EUROPEAN ORDERS GREATER THAN £500.00 ex VAT DELIVERED FREE    /    WE SHIP WORLDWIDE
    Share this page on Facebook   Share this page on LinkedIn   Share this page on Twitter   Share this page on Whatsapp   

    Rapid Ref : 0330-0178  

    GCE 4-218 Propane Cutting Tip
    0330-0178

    £52.50  EX VAT
    SSP Suggested Selling Price = £65.63  YOU SAVE £13.13
     Buy in 3 easy interest free payments of £17.50† with

    Victor Type 218 One Piece Propane Nozzle.

    For deseaming, scarfing, gouging, weld preparation, removing defective welds, rivet washing.

    Model No: 4-218
    Tip Size: 4
    Material Thickness: 75mm
    Pressure:
    Oxygen - 3.10 Bar
    Acetylene - 0.52 Bar

    ESAB GCE Gas Torch Parts FAQs

    Replacement nozzles, heating tips, mixers and elbows for oxy-fuel torches: how to identify the right part and keep the torch working safely.

    How do I choose the right size of cutting nozzle?icon-minus-redicon-plus-red

    The diameter of the cutting oxygen hole is chosen according to the thickness of the material. Thicker steel needs a larger cutting orifice and more preheat, so the nozzle size has to suit the job.

    Nozzle size numbers are not standard between makers, so do not rely on the number alone. Use the chart supplied with your torch, which links nozzle size to material thickness and gives the gas pressures to set. Check the maker's markings on the old nozzle, and use the same fuel gas the nozzle was designed for. If you are unsure which part you have, our team can help you identify it.

    Why are some nozzles one-piece and others two-piece?icon-minus-redicon-plus-red

    The type of nozzle depends on the fuel gas, on whether the torch is used by hand or on a machine, and on the maker's preference. Nozzles for acetylene are usually one-piece, while machine cutting may use two-piece designs.

    In practice, a two-piece nozzle has an inner and outer part that fit together, and the shape of the fitting affects how the gases reach the flame. You cannot assume that different designs will swap over. Look at how the old nozzle seats in the torch head, check the manual, and replace like with like unless the torch maker says otherwise.

    Why does my torch backfire, and what should I check?icon-minus-redicon-plus-red

    A backfire is the flame burning back into the torch, often with a sharp bang. It may happen when the torch is held too close to the workpiece, or when the nozzle is partly blocked. Backfires do not usually cause injury or damage, but can indicate a fault in the equipment.

    If one occurs, shut the torch valves (oxygen first, then fuel), close both cylinder valves, cool the torch if necessary and then inspect the equipment, especially the nozzle. Do not relight until you have found the cause. A damaged, blocked or badly seated nozzle should be cleaned or replaced.

    How do I test the torch and nozzle connections for leaks?icon-minus-redicon-plus-red

    Use a proprietary leak detecting spray or solution made for oxy/fuel systems, and do not use soapy water or any solution containing grease or oil on oxygen systems. Never look for a gas leak with a naked flame.

    Repair or replace any leaking component immediately. Check the nozzle nut and seating, the torch valves and every hose connection, and do this regularly. Equipment used in tough conditions normally needs more frequent checks. If a leak will not stop after tightening a fitting properly, take that equipment out of use and have it repaired or replaced.

    Shop Similar Categories