WE HAVE SOME GREAT LIMITED-TIME OFFERS - CLICK HERE TO VIEW THEM WE SHIP WORLDWIDE    /    All UK ORDERS GREATER THAN £75 EX VAT DELIVERED FREE    /    WE SHIP WORLDWIDE    /    ALL EUROPEAN ORDERS GREATER THAN £500.00 ex VAT DELIVERED FREE    /    WE SHIP WORLDWIDE
    Share this page on Facebook   Share this page on LinkedIn   Share this page on Twitter   Share this page on Whatsapp   

    Rapid Ref : 501030-SET11  

    HMT VersaDrive STAKIT ETOP4 Impact Reamer 11 Piece Set (8 - 26mm)
    501030-SET11

    £806.99  EX VAT
    SSP Suggested Selling Price = £949.40  YOU SAVE £142.41
     Buy in 3 easy interest free payments of £269.00† with

    HMT VersaDrive reamers are the perfect hole alignment and enlarging tool for metalworkers & steel erectors to keep the job moving when a hole is misaligned or the incorrect size for the fixing.

    Featuring a specially designed six-flute cutting geometry and Titanium coating, VersaDrive Reamers are fully Impact rated and perform fastest when used with an Impact Wrench, providing ultimate cutting performance with virtually no power tool kickback.

    VersaDrive Reamers have a patented non-slip Hex shank suitable for use in any standard 1/2” drill chuck for Pistol Drills or used with a VersaDrive Rapid Lock adaptor for use in a wide range of power tools such as Magnetic Drills.

    • Precision six-flute design for smooth cutting
    • Safer reaming with minimal kickback
    • Specially hardened for use with impact tools
    • High-grade tool steel for high accuracy and long life
    • High strength, non-slip shank design
    • Goldmax low-friction titanium coating to stop burnout
    • Use on Impact or Rotary

    Product Details

    Brochures & Manuals

    BROCHURES & MANUALS
       View Brochure

    HMT Reamers FAQs

    Answers to common questions about choosing and using reamers for enlarging and aligning holes in steelwork.

    What is a reamer used for on steelwork?icon-minus-redicon-plus-red

    A reamer enlarges and cleans up an existing hole to a more accurate size and a smoother finish. In structural steelwork it is commonly used during erection, when plates or sections have been bolted loosely together and the holes do not quite line up, so that a bolt can pass through without damaging its thread.

    The result is a slightly larger or elongated hole, so it is a tool for small, local misalignment rather than a general way to make holes. Check the connection requirements for your job before reaming.

    Can a reamer fix a hole that is in the wrong place?icon-minus-redicon-plus-red

    No. A reamer follows the hole that is already there, so it will not correct a hole that is off position or not straight. It can deal with small, local misalignment between plies, but only by removing the minimum material needed.

    If holes are badly out, reaming is the wrong answer and the connection may need to be reviewed by the person responsible for the design. Do not try to fill mislocated holes by welding without that advice.

    How much material should I leave for the reamer to remove?icon-minus-redicon-plus-red

    Too little and the reamer rubs instead of cutting, which creates heat, wears the tool and can leave the hole undersize. Too much and the hole can end up oversize with a rough finish.

    For machine reaming, the allowance usually depends on the material, the hole diameter and the finish of the pre-drilled hole, and is typically a small percentage of the diameter. The reamer maker's guidance is the best starting point for the exact amount, and for site work on structural joints follow the job specification.

    What eye protection should I wear when reaming?icon-minus-redicon-plus-red

    Wear eye protection suited to the job. The HSE lists working with power-driven tools, where debris or chippings may fly into the face, as a case where eye protection is needed, and says it should be appropriate for the task and fit the wearer properly.

    Safety glasses with side protection are the minimum for most reaming; goggles or a face shield may be better where chips are thrown. Do not use compressed air to blow swarf away, because it can bounce back into the eyes. Use a brush or a vacuum instead, with the tool stopped.

    Shop Similar Categories