WE HAVE SOME GREAT LIMITED-TIME OFFERS - CLICK HERE TO VIEW THEM WE SHIP WORLDWIDE    /    All UK ORDERS GREATER THAN £75 EX VAT DELIVERED FREE    /    WE SHIP WORLDWIDE    /    ALL EUROPEAN ORDERS GREATER THAN £500.00 ex VAT DELIVERED FREE    /    WE SHIP WORLDWIDE
    Share this page on Facebook   Share this page on LinkedIn   Share this page on Twitter   Share this page on Whatsapp   

    Rapid Ref : 7900860X3-K3  

    BRB 4 Boiler Pipe Preparation Machine, Kit 3, Standard Clamp, Pipe ID Clamping Range: 32 - 110.8mm
    7900860X3-K3

    Select Option 
    Prices From £5005.00 ex VAT

    Lightweight and robust Boiler Prep Machine. Counterboring and axial turning of pipes made from high-alloy steel (stainless steel), low-alloy and carbon steel with the unique tool system QTC®. Designed for pipe end preparations and boiler pipe applications.

    The BRB machines are available in the following drive versions:

    Electric:
    230 V, 50/60 Hz EU or 120 V, 50/60 Hz EU/US.
    Electric drive with single-phase AC motor. Protection class II (double insulated). Built-in electronic variable cutting speed.

    Pneumatic:
    Pneumatic power drive. The manufacturer’s warranty can only be given when using the original Orbitalum mobile air unit, Code 790 093 060 (click here to view).

    Pneumatic/Auto:
    Pneumatic multi-disc or with an additional pneumatic clamping system.

    When installing or repairing boiler pipes, time is of the essence - the new pneumatic clamping system greatly reduces the time to clamp and release the machine, improving efficiency. The machine centres itself on the inside diameter of the pipe and then clamps automatically by using the toggle switch, likewise, the toggle switch releases the clamping after the machining operation. This is why the BRB with automatic pneumatic clamping is ideal for continuous production e.g. boiler and heat exchanger applications.

    Brochures & Manuals

    BROCHURES & MANUALS
       View Brochure

    BRB 2 & BRB 4 with Std Clamp FAQs

    Answers to common questions about internally clamped boiler tube preparation machines, from choosing a clamp kit to safe use and care.

    Why is the bevel on a boiler tube important for the weld?icon-minus-redicon-plus-red

    The bevel gives the welder access to the root of the joint so the first pass can fuse properly. Poor preparation is a recognised cause of incomplete root fusion: a root face that is too thick, a root gap that is too small, or a bevel angle that is too small can all stop the arc reaching the root.

    The bevel angle, root face and root gap are normally set by the welding procedure for the job, so cut to that. A machined bevel is uniform all round the tube, which makes it easier to hold the correct gap than hand grinding does.

    Why use a cold-cutting machine rather than thermal cutting?icon-minus-redicon-plus-red

    A machine like this removes metal with cutting tools rather than heat. Thermal cutting creates a heat-affected zone, a band of metal beside the cut whose properties have changed, and these changes are usually undesirable because they can reduce toughness or corrosion resistance and increase the risk of cracking.

    Mechanical preparation avoids that zone and leaves a clean, square face ready for welding. It also removes the oxidised edge that thermal cutting leaves, which would otherwise need grinding off. Follow the maker's advice for the material being cut.

    How do I make the machine safe before changing tools or the clamp?icon-minus-redicon-plus-red

    Stop the machine and make sure the moving parts have stopped, then isolate the power supply before you touch the tooling. For an air-driven machine that means shutting off and disconnecting the air, and releasing any stored pressure so nothing can move or cycle unexpectedly.

    Most maintenance should be done with the power off, and the machine should be locked off if there is any chance it could be switched back on by someone else. Follow the maker's instructions, and make sure the person doing the work is competent to do it.

    What protective equipment and clothing should I use when machining tube ends?icon-minus-redicon-plus-red

    Your risk assessment decides, but it will normally include eye protection suited to flying chips and swarf, and hearing protection where the machine is noisy. The HSE explains that PPE must be assessed as suitable before use, maintained and stored properly, and that users need instruction and training in it.

    Keep clothing close-fitting and hair tied back. Regulators warn that gloves can increase the risk of entanglement and are not acceptable near rotating parts, so do not wear loose gloves while the head is turning. Handle sharp swarf and freshly cut ends only when the machine has stopped.

    Shop Similar Categories