WE HAVE SOME GREAT LIMITED-TIME OFFERS - CLICK HERE TO VIEW THEM WE SHIP WORLDWIDE    /    All UK ORDERS GREATER THAN £75 EX VAT DELIVERED FREE    /    WE SHIP WORLDWIDE    /    ALL EUROPEAN ORDERS GREATER THAN £500.00 ex VAT DELIVERED FREE    /    WE SHIP WORLDWIDE
    Share this page on Facebook   Share this page on LinkedIn   Share this page on Twitter   Share this page on Whatsapp   

    Rapid Ref : CK-D2GSXXX  

    CK 2 Series Complete Front End Gas Saver Kit, Alumina Cup
    CK-D2GSXXX

    Select Option 
    Prices From £19.18 ex VAT

    CK Worldwide's Gas Saver™ front-end kit allows users to save up to 40% of shield gas consumption while providing better shield gas coverage patterns. With better shielding gas coverage patterns the welder can extend the tungsten up to 6 x the diameter of the electrode beyond the edge of the gas cup (This is achieved in draft-free areas using argon gas).

    Alumina push-on or Pyrex high-temperature glass cups are available. Alumina cups are durable, impact-resistant and handle high-temperature welding applications. Pyrex glass cups are used in applications where visibility is an issue such as inside corners, inside pipe, around tubing, etc.

    The Gas Saver kits will retrofit 2 series (CK9, CK20) or competitive brand equivalents using a replaceable white Teflon heat shield on a silicon rubber torch body.


    CK Gas Saver Kits

    Product Details

    CK 2 Series Gas Saver Kits FAQs

    Gas lens front-end kits for small TIG torches: what they do, how to choose the cup and how to get the best shielding from them.

    How is a gas lens different from a standard collet body?icon-minus-redicon-plus-red

    Both hold the collet and tungsten and carry gas to the cup. The difference is the gas path. A standard collet body passes gas through a few ports, so the flow can swirl and may draw air into the shield. A gas lens passes it through mesh screens first, giving a calmer, more column-like flow.

    That usually allows a longer tungsten extension and better coverage in awkward positions. A standard collet body is still perfectly adequate for a lot of general work in still air, and it works with the plain cups that normally come with the torch. A gas lens also needs a cup made to fit it, so the parts are bought as a matched set.

    Will a gas saver kit really use less gas, and how do I set the flow?icon-minus-redicon-plus-red

    Because the flow leaving the cup is smoother, a gas lens can often shield well at a lower flow than the same size cup on a standard collet body. In one training example a number 8 cup needed about 10 litres per minute with a standard body but about 5 with a gas lens. How much you save depends on the cup size, the job and draughts, so treat headline percentages as best-case figures.

    There is no single exact rule for the setting, so start from the maker's guidance for your cup and torch, then reduce to the lowest flow that still gives clean, bright welds. Too much flow causes turbulence, can pull air in and can make the arc unstable. Flowmeters are not always accurate, so a flow tester is a useful check.

    How far can I extend the tungsten with a gas lens?icon-minus-redicon-plus-red

    Keep the tungsten extension as short as the joint allows. A gas lens holds its shield over a longer distance than a standard collet body, so more extension is possible, and larger cups allow longer extension still. Gas lens kit makers quote a maximum extension for ideal, draught-free conditions with argon, but treat any such figure as a best case and follow the instructions for your kit.

    Extension that is too long lets air reach the weld pool and tungsten, and a torch maker's troubleshooting guide lists excessive electrode extension as a cause of tungsten inclusions. If you see porosity, discoloured welds or a dirty tungsten, shorten the extension or move up a cup size first.

    Should I choose an alumina cup or a glass cup?icon-minus-redicon-plus-red

    Alumina (ceramic) cups are the more durable choice and suit general work and a busy workshop. Glass (borosilicate) cups let you see through to the arc and the joint, which helps in inside corners, inside pipe and around tubing where a solid cup blocks the view.

    The trade-off is that glass is more fragile and breaks more easily if the torch is dropped or knocked. Check the maker's guidance for the current each cup type can handle, and replace any cup that is cracked or chipped. Many welders keep both types and swap depending on the job.

    Shop Similar Categories