The website is working fine. Please feel free to place orders. WE SHIP WORLDWIDE    /    All UK ORDERS GREATER THAN £75 EX VAT DELIVERED FREE    /    WE SHIP WORLDWIDE    /    ALL EUROPEAN ORDERS GREATER THAN £500.00 ex VAT DELIVERED FREE    /    WE SHIP WORLDWIDE
    Share this page on Facebook   Share this page on LinkedIn   Share this page on Twitter   Share this page on Whatsapp   

    Rapid Ref : 131324R51C  

    ESAB OK Tigrod 55, 2.4mm x 500mm TIG Wire, 1Kg Pack, ER100S-G
    131324R51C

    £86.69  EX VAT
    SSP Suggested Selling Price = £97.13  YOU SAVE £10.44
     Buy in 3 easy interest free payments of £28.90† with

    Meet OK Tigrod 55 (formerly OK Tigrod 13.13), a copper-coated, low alloyed, chromium-nickel-molybdenum (0,5% Cr, 0,5% Ni, 0,2% Mo) rod that's not just for GTAW of high-strength steels with a minimum tensile strength of 690 MPa. It's also your go-to for welding steels that require good impact strength at low temperatures.

    Brochures & Manuals

    BROCHURES & MANUALS
       View Brochure

    ESAB Consumables FAQs

    Practical answers on choosing, storing and using welding wire and stick electrodes.

    How do I choose the right MIG wire diameter and shielding gas?icon-minus-redicon-plus-red

    Wire diameter and wire feed speed together set the welding current, because the wire burns off at a rate that settles in balance with the feed speed. Thicker material and higher current generally call for a larger diameter, while thin sheet suits finer wire. Your welder's manual and the wire data sheet show which diameters the machine is built for.

    For steels, typical shielding gases are carbon dioxide or argon mixed with carbon dioxide or a little oxygen. Non-ferrous metals normally use argon. The right gas depends on the wire, the metal and the transfer mode, so follow the wire maker's recommendation.

    What is the difference between solid wire and flux-cored wire?icon-minus-redicon-plus-red

    Solid wire is a single strand and needs an external shielding gas. It usually gives little spatter and no slag to chip off, which suits clean, thinner work where appearance matters. Flux-cored wire is a tube filled with flux. Some types still use gas, while self-shielded types do not, which helps outdoors where wind can blow gas away.

    Flux-cored wire generally tolerates dirtier or scaled steel and is often chosen for thicker material and higher deposition, but with slag to remove afterwards. Neither is better in every case. Choose by thickness, location, gas supply and what your welder is designed to run.

    How do I match a TIG filler rod to the metal I am welding?icon-minus-redicon-plus-red

    The weld pool is a mixture of the parent metal and the filler, so the rod is normally chosen to suit the parent metal. Carbon steel, low alloy steel and stainless each have their own rods, and low alloy heat-resistant steels need a rod made for that alloy. Using a general-purpose rod on everything is a common mistake.

    In TIG the filler is added to the weld pool by hand, separately from the arc, and argon is the usual gas for steels and stainless. Check the rod's data sheet or the standard named on its pack, and follow your welding procedure if the job is specified.

    Why are low hydrogen electrodes supplied in sealed packs?icon-minus-redicon-plus-red

    Low hydrogen electrodes are used where hydrogen cracking in the weld or heat affected zone must be avoided, such as on critical or more hardenable steels. Their coating picks up moisture from the air, which adds hydrogen to the weld. Sealed packs let you use them straight from the pack, with no baking needed beforehand.

    If a pack has been opened or damaged, the electrodes should be re-dried as the maker instructs and then kept warm or limited in their exposure time. Exact temperatures and times differ between makers, so follow the instructions on the pack and your job specification.

    Shop Similar Categories