WE HAVE SOME GREAT LIMITED-TIME OFFERS - CLICK HERE TO VIEW THEM WE SHIP WORLDWIDE    /    All UK ORDERS GREATER THAN £75 EX VAT DELIVERED FREE    /    WE SHIP WORLDWIDE    /    ALL EUROPEAN ORDERS GREATER THAN £500.00 ex VAT DELIVERED FREE    /    WE SHIP WORLDWIDE
    Share this page on Facebook   Share this page on LinkedIn   Share this page on Twitter   Share this page on Whatsapp   

    Rapid Ref : 0700000804  

    ESAB Sentinel A50 Helmet Shell
    0700000804

    £57.79  EX VAT
    SSP Suggested Selling Price = £77.05  YOU SAVE £19.26
     Buy in 3 easy interest free payments of £19.26† with

    ESAB shell for Sentinel A50 welding helmet.

    The ESAB Sentinel A50 Welding Helmet Shell is the ultimate in welding protection. With its lightweight design, comfortable fit, and advanced features, the Sentinel A50 provides superior protection for your eyes, face, and neck.

    Brochures & Manuals

    BROCHURES & MANUALS
       View Brochure

    ESAB Sentinel A50 Parts FAQs

    Spare lenses, filters, headgear and other parts for an auto-darkening welding helmet, and how to match and look after them.

    What is the difference between a front cover lens and an inside cover lens?icon-minus-redicon-plus-red

    The front cover lens is the clear plate on the outside of the filter. It takes the heat, spatter and scratches, so it is the part that wears first. The inside cover lens sits behind the filter, on the wearer's side.

    Both are replaceable parts. A helmet maker's manual says the auto-darkening filter must only be used with the inner cover lens fitted, and another maker describes the outside and inside lenses as consumables to be replaced with the maker's own spares. Some ranges include different grades of front cover, such as clear, tinted or tougher types, so check which your helmet accepts in the manual.

    When should I replace a cover lens?icon-minus-redicon-plus-red

    A helmet maker's manual says to replace a cracked, scratched or pitted front cover lens regularly, and a second maker says lenses must be replaced if broken, damaged or covered in spatter to the point that vision is impaired. Replace the inside cover lens if it is damaged too.

    There is no single hours or welds figure that suits everyone, because it depends on the process, the current and how much spatter you produce, so check the covers before each job. On a new cover lens, make sure the protective film has been removed, as the manual lists a left-on film as a cause of poor vision. Fit it as the manual shows.

    What should I do if the filter does not darken?icon-minus-redicon-plus-red

    Stop welding straight away. A helmet maker's manual says that if the helmet does not darken when an arc is struck you must stop welding immediately and contact your supervisor or dealer. Another maker's manual says to stop using the filter if any of its function tests fail, and warns that unprotected exposure to the arc can seriously damage the eyes.

    The manual's troubleshooting list for a filter that does not darken or flickers is: a soiled or damaged front cover lens, dirty sensors, sensitivity set too low for the current, and a weak or poorly fitted battery. If none of those cures it, do not use the helmet. Never open or tamper with the filter.

    How should I look after the helmet and its parts between jobs?icon-minus-redicon-plus-red

    PPE must be properly looked after and stored when not in use, for example in a dry, clean cupboard, and reusable PPE must be cleaned and kept in good condition. Use the correct replacement parts, following the manufacturer's schedule.

    Helmet maker manuals add some specifics: keep the sensors and solar cells clean, store the helmet in a cool, dry, dark place, remove the battery before long storage, and avoid setting the helmet down on its front cover lens. Carry spare lenses somewhere clean and dry. Inspect the helmet before each use and replace damaged covers, headgear or shells rather than carrying on.

    Shop Similar Categories