WE HAVE SOME GREAT LIMITED-TIME OFFERS - CLICK HERE TO VIEW THEM WE SHIP WORLDWIDE    /    All UK ORDERS GREATER THAN £75 EX VAT DELIVERED FREE    /    WE SHIP WORLDWIDE    /    ALL EUROPEAN ORDERS GREATER THAN £500.00 ex VAT DELIVERED FREE    /    WE SHIP WORLDWIDE
    Share this page on Facebook   Share this page on LinkedIn   Share this page on Twitter   Share this page on Whatsapp   

    Rapid Ref : 209015-SET1  

    HMT VersaDrive TurboTip Impact Drill Bit InsertFoam 4 Piece Set (6, 8, 10, 12mm)
    209015-SET1

    Click here to see what's included

    £124.91  EX VAT
    SSP Suggested Selling Price = £146.95  YOU SAVE £22.04
     Buy in 3 easy interest free payments of £41.64† with

    This product is included in the latest promotion from HMT! Valid until December 21st, save £67.95 with this limited time offer. HMT OD26 VersaDrive TurboTip Impact Drill Bit InsertFoam 4 Piece Set (6, 8, 10, 12mm)

    HMT VersaDrive TurboTip Impact drill bits are stepped tip bits that drill twice the speed of standard bits without pilot drilling while cutting a perfectly round hole.

    Turbocharge your drilling performance using this revolutionary tool with an impact wrench /driver. Double-hardened and titanium-coated for faster drilling & reduced wear.

    VersaDrive TurboTip drill bits have a patented non-slip Hex shank suitable for use in any standard 1/2" drill chuck for cordless or pistol drills or used with a VersaDrive Rapid Lock adaptor for use in a wide range of power tools such as Magnetic Drills.

    • No pilot drilling needed
    • Patented Drill Point
    • 50% Faster Drilling with 30% less pressure
    • Incredible Finished Hole quality
    • Instant drill starts with no slipping
    • No 'snatch' when the drill bit breaks through
    • Fully Impact rated on structural steel
    • Fantastic Tool Life

    Product Details

    Brochures & Manuals

    BROCHURES & MANUALS
       View Brochure

    HMT Drill Bits FAQs

    Answers to common questions about choosing and using cobalt, impact and general purpose drill bits for steel.

    What loose clothing, hair or glove precautions apply when drilling?icon-minus-redicon-plus-red

    Drills are rotating machinery, and entanglement is a serious risk. The HSE advises avoiding loose or baggy clothing, tying back or covering long hair, and avoiding jewellery, including rings, when operating engineering machinery. It also says many serious workshop accidents could be avoided if gloves were not worn near rotating machinery such as drills and lathes.

    Follow the instructions for your drill or drilling machine and your own risk assessment. Keep hands clear of the bit while it is turning.

    Do I need cutting fluid when drilling steel, and how do I use it?icon-minus-redicon-plus-red

    For steel, and especially stainless, cutting fluid is normally worthwhile. It carries heat away, reduces friction and helps the swarf clear. Apply it continuously if you can, or stop regularly to reapply it, rather than letting the bit run dry.

    Use a proper cutting oil or metalworking fluid; thin sprays tend to evaporate quickly. Aluminium and brass can often be drilled with a light lubricant or dry, depending on the material and the job. Follow the bit maker's advice for the material you are drilling.

    What is the difference between cobalt and standard HSS drill bits?icon-minus-redicon-plus-red

    Cobalt steel is a variation of high speed steel with a higher cobalt content, usually described by grades with roughly 5 and 8 per cent cobalt. The cobalt gives much better red hardness, meaning the bit keeps its hardness at high cutting temperatures, so cobalt bits suit tough jobs such as stainless steel, hard steel, cast iron and high-tensile bolts.

    Standard HSS is usually adequate for mild steel, aluminium, brass and plastics. Cobalt bits are often a little more brittle, so avoid side-loading them and do not drill at an angle. Because grades vary, check the markings and the maker's guidance for your material.

    What drill size do I need before tapping a thread?icon-minus-redicon-plus-red

    The hole before tapping must be a specific 'tap drill' size, slightly smaller than the thread's nominal diameter, to leave material for the thread to form. A tool maker explains that a hole that is too small forces the tap to remove too much material and risks binding and breaking it, while one that is too large gives shallow threads that can strip.

    Charts often assume a high thread percentage, and a lower percentage that allows a slightly larger drill can make tapping easier. Charts also differ with whether the tap cuts or forms the thread, so use the chart supplied with your tap or the tap maker's data. Drill the hole straight and square to the surface.

    Shop Similar Categories