WE HAVE SOME GREAT LIMITED-TIME OFFERS - CLICK HERE TO VIEW THEM WE SHIP WORLDWIDE    /    All UK ORDERS GREATER THAN £75 EX VAT DELIVERED FREE    /    WE SHIP WORLDWIDE    /    ALL EUROPEAN ORDERS GREATER THAN £500.00 ex VAT DELIVERED FREE    /    WE SHIP WORLDWIDE
    Share this page on Facebook   Share this page on LinkedIn   Share this page on Twitter   Share this page on Whatsapp   

    Rapid Ref : STC-ETOP4-F04  

    HMT VersaDrive STAKIT Full Top Case + Adaptor Foam Inserts
    STC-ETOP4-F04

    £80.09  EX VAT
    SSP Suggested Selling Price = £94.22  YOU SAVE £14.13
     Buy in 3 easy interest free payments of £26.70† with

    The STAKIT Top Case takes either 

    • 2 x Large InsertFoams   or
    • 4 x Small InsertFoams   or
    • 1 x Large InsertFoam & 2 x Small InsertFoams

     

    The STC-ETOP4-F04 case comes complete with three foam inserts to hold five VersaDrive adaptors (1/4" Impact adaptor, 1/2" Impact adaptor, 3/4" Impact adaptor, magnet drill adaptor, 130mm extension arbor or SDS+ adaptor).

    Customisable to each application, these sets can grow as you add to your STAKIT system. This case will clip to other Top cases or onto any EMID box.

    Related Items

    HMT VersaDrive STAKIT Top Cases FAQs

    Practical answers on choosing and using top cases for impact drilling, reaming, threading and rivet removal bits.

    What is an impact reamer used for?icon-minus-redicon-plus-red

    On steel structures, holes in joining members are sometimes slightly out of line. A reamer removes a little material so the holes line up and the bolt can pass without force, and a tapered tip helps it enter holes that are not quite aligned.

    It is for correcting small misalignments, not for drilling new holes. Take off only the minimum needed, because enlarged holes can affect the joint. On structural steelwork, check the project specification and ask the designer or engineer before reaming, and do not use a reamer to cover up badly mismatched holes. Not every reamer is built for impact driver use, so check the maker's information.

    What is the difference between a thread die and a thread chaser?icon-minus-redicon-plus-red

    A thread die is a cutting tool that makes a new external thread on a bar or rod. A thread chaser is designed to clean, re-form and restore an existing thread that is dirty, rusty or lightly damaged.

    A cutting tool run over a damaged thread can remove more thread material than you want, so a chaser is the gentler choice where most of the thread is intact. Chasing only works if enough thread remains: if a bolt or stud is stripped, galled or badly mangled, replace it. Check the thread size and pitch first, and use cutting fluid when cutting a new thread.

    Does a sharp bit really make a difference to vibration and speed?icon-minus-redicon-plus-red

    Yes. HSE advises checking tools before use to avoid the extra vibration caused by faults or general wear, and keeping cutting tools sharp so that they stay efficient. A worn drill bit makes you push harder, builds heat and can leave a rough hole.

    Check your bits for a dulled cutting edge, chipped lips, bluing from heat or bending. Replace damaged bits rather than forcing them. Bits that cut cleanly need less pressure, which is better for the hole, the driver and your hands.

    How long can I use an impact tool before vibration becomes a concern?icon-minus-redicon-plus-red

    There is no single safe time, because it depends on the tool, how it is used and the person. HSE gives a rough guide that hammer-action tools used for more than about 15 minutes a day, or some rotary and other action tools for more than about an hour a day, may mean a vibration exposure problem. Real limits depend on the maker's vibration data.

    Watch for tingling and numbness in the fingers, not being able to feel things, or loss of strength in the hands, and report them early. Check the maker's vibration figures and your employer's risk assessment, and plan job rotation and breaks to cut the time the tool is actually running.

    Shop Similar Categories