WE HAVE SOME GREAT LIMITED-TIME OFFERS - CLICK HERE TO VIEW THEM WE SHIP WORLDWIDE    /    All UK ORDERS GREATER THAN £75 EX VAT DELIVERED FREE    /    WE SHIP WORLDWIDE    /    ALL EUROPEAN ORDERS GREATER THAN £500.00 ex VAT DELIVERED FREE    /    WE SHIP WORLDWIDE
    Share this page on Facebook   Share this page on LinkedIn   Share this page on Twitter   Share this page on Whatsapp   

    Rapid Ref : CK-CK510  Mfr Ref : CK510

    CK 510 Torch Body Water Cooled 500A 70° Rg
    CK510 CK-CK510

    £90.28  EX VAT
    SSP Suggested Selling Price = £180.55  YOU SAVE £90.28
     Buy in 3 easy interest free payments of £30.09† with

    CK510 Torch Parts FAQs

    Spares for a water-cooled TIG torch: the front-end parts, back caps and hoses, how to tell what is worn and how to order the right part.

    How do I check water hoses for leaks, and why does it matter?icon-minus-redicon-plus-red

    Before striking an arc, run the cooler and look and feel along the hoses and at every connection for drips, bulging, thinning walls, kinks or cracks. One maker's manual says to check all coolant connections for tightness and leaks at every start-up, and never to operate a water-cooled torch without coolant. A leak can also let coolant reach the floor and equipment, which adds an electric shock risk.

    The insulation on welding torches and cables should be undamaged, equipment should be checked before use, and unserviceable equipment should be withdrawn and marked as not for use. Do not tape over a leak as a repair.

    Why do I get porosity or poor gas shielding after changing torch parts?icon-minus-redicon-plus-red

    A maker's TIG troubleshooting guide lists a blocked or leaking gas hose or torch, a loose connection, excessive tungsten stick-out, draughts and too much gas turbulence as causes of inadequate shielding and porosity. After a parts change, check that the gas hose connections are tight, the collet body or gas lens is seated, the back cap is fitted with its O-ring in good condition, and the cup is undamaged.

    The same guide suggests gas lens or gas saver parts where turbulence is the problem, and reducing the stick-out or fitting a larger cup. Recheck assembly against your torch manual before changing gas settings, and keep the gas supply and hoses leak-free.

    How do I match the collet and collet body to my tungsten electrode?icon-minus-redicon-plus-red

    Torch makers list collets and collet bodies by tungsten diameter and by torch series, so you need both pieces of information. Check the diameter of the tungsten you actually use, then check the torch series from the torch manual, the markings on the body, or the old part if it carries a size marking.

    A collet that is the wrong size will not clamp the electrode evenly, which causes poor current transfer, overheating and a tungsten that slips. Parts that look alike across torch series are often not interchangeable, because thread patterns differ, so confirm the match before ordering rather than relying on appearance.

    How do I tell a worn collet, collet body, cup or back cap O-ring?icon-minus-redicon-plus-red

    A maker's troubleshooting guide links short collet life and excessive electrode consumption to heat inside the torch, and says an ordinary collet can split, twist or jam and should be replaced. A collet or collet body that looks discoloured, distorted or pitted, or that no longer grips the tungsten firmly, is due for replacement. A cup that cracks or shatters in use should also be replaced.

    On the back cap, look for a cracked, flattened or dried-out O-ring, because that ring seals the rear of the torch and a damaged one can leak gas. Do not run the torch above its rating, because overheating wears these parts faster.

    Shop Similar Categories