WE HAVE SOME GREAT LIMITED-TIME OFFERS - CLICK HERE TO VIEW THEM WE SHIP WORLDWIDE    /    All UK ORDERS GREATER THAN £75 EX VAT DELIVERED FREE    /    WE SHIP WORLDWIDE    /    ALL EUROPEAN ORDERS GREATER THAN £500.00 ex VAT DELIVERED FREE    /    WE SHIP WORLDWIDE
    Share this page on Facebook   Share this page on LinkedIn   Share this page on Twitter   Share this page on Whatsapp   

    Rapid Ref : 601038-0010  

    HMT ULTRA Coated Weldon Shank 82° TCT Countersink 1-1/4"
    601038-0010

    £390.45  EX VAT
    SSP Suggested Selling Price = £459.35  YOU SAVE £68.90
     Buy in 3 easy interest free payments of £130.15† with

    Premium countersink with three times heavy-duty tungsten carbide brazed inserts for maximum life in challenging materials. Standard 19.05mm Weldon shank for use in all standard magnet drills. A 101013 Morse taper arbor can be used in a pillar drill press or radial drill.

    1-1/4" max diameter. 3/4" (19.05mm) Weldon shank to fit all standard magnet drills.

    HMT Countersinks FAQs

    Answers to common questions about choosing and using countersinks for magnetic drills, drill presses and power drills.

    Should I choose an 82 degree or a 90 degree countersink?icon-minus-redicon-plus-red

    Match the countersink angle to the screw head. Metric countersunk screws, including metric flat head socket screws, normally have a 90 degree head. Inch (UNC/UNF) flat head screws normally have an 82 degree head.

    The two are not interchangeable. A 90 degree head in an 82 degree recess sits deeper and leaves a gap around the edge. An inch head in a 90 degree recess tends to stand proud of the surface. Check the screw standard or the head drawing if you are unsure, and cut a test piece before you start on the real work.

    How large should the countersink diameter be for a given screw?icon-minus-redicon-plus-red

    The countersunk diameter at the surface should be slightly larger than the maximum diameter of the screw head, so the head can seat fully and finish flush. The allowance needed is small, so use the screw maker's head dimensions or a fastener table rather than guessing.

    The clearance hole must already be the right size for the screw shank, and the countersink cutter must be big enough to cut the full recess diameter. For a pattern of holes, trial one on an offcut of the same material and thickness, then check the screw sits as intended before committing to the job.

    How do I get the screw heads to sit flush and not stand proud or sink too far?icon-minus-redicon-plus-red

    Depth controls how far the head sits. Too shallow and the head stands proud; too deep and it sinks below the surface and loses bearing area. Cut a little at a time and test-fit a screw, rather than cutting to full depth in one go.

    A depth stop, or a fixed depth setting on the machine, helps keep every hole in a pattern the same. Because material hardness and thickness vary, trial the setting on a scrap piece first, and re-check the first holes of each batch.

    What safety precautions should I take with loose clothing, hair and gloves when countersinking?icon-minus-redicon-plus-red

    Countersinking uses rotating tools, so entanglement is a real risk. The HSE advises avoiding loose or baggy clothing, tying back or covering long hair, and avoiding jewellery, including rings, when operating engineering machinery. It also says many serious workshop accidents could be avoided if gloves were not worn near rotating machinery such as drills.

    Follow the machine maker's instructions and your own risk assessment. Hold or clamp the work securely so it cannot spin with the cutter, and keep hands clear of the rotating tool.

    Shop Similar Categories