WE HAVE SOME GREAT LIMITED-TIME OFFERS - CLICK HERE TO VIEW THEM WE SHIP WORLDWIDE    /    All UK ORDERS GREATER THAN £75 EX VAT DELIVERED FREE    /    WE SHIP WORLDWIDE    /    ALL EUROPEAN ORDERS GREATER THAN £500.00 ex VAT DELIVERED FREE    /    WE SHIP WORLDWIDE
    Share this page on Facebook   Share this page on LinkedIn   Share this page on Twitter   Share this page on Whatsapp   

    Rapid Ref : 603065  

    HMT VersaDrive Countersinks - 82°
    603065

    Select Option 
    Prices From £22.02 ex VAT

    The HMT VersaDrive Countersink is a premium quality countersink with fully ground flutes and Titanium coating to help reduce wear and blunting.

    VersaDrive Countersinks have a patented non-slip Hex shank suitable for use in any standard 1/2” drill chuck for cordless or pistol drills or used with a VersaDrive Rapid Lock adaptor for use in a wide range of power tools such as Magnetic Drills.

    Utilise the convenience and power of an impact wrench to quickly deburr and countersink holes up to 16.5mm with minimal torque kick-back against the operator.

    HMT Countersinks FAQs

    Answers to common questions about choosing and using countersinks for magnetic drills, drill presses and power drills.

    Should I choose an 82 degree or a 90 degree countersink?icon-minus-redicon-plus-red

    Match the countersink angle to the screw head. Metric countersunk screws, including metric flat head socket screws, normally have a 90 degree head. Inch (UNC/UNF) flat head screws normally have an 82 degree head.

    The two are not interchangeable. A 90 degree head in an 82 degree recess sits deeper and leaves a gap around the edge. An inch head in a 90 degree recess tends to stand proud of the surface. Check the screw standard or the head drawing if you are unsure, and cut a test piece before you start on the real work.

    How do I get the screw heads to sit flush and not stand proud or sink too far?icon-minus-redicon-plus-red

    Depth controls how far the head sits. Too shallow and the head stands proud; too deep and it sinks below the surface and loses bearing area. Cut a little at a time and test-fit a screw, rather than cutting to full depth in one go.

    A depth stop, or a fixed depth setting on the machine, helps keep every hole in a pattern the same. Because material hardness and thickness vary, trial the setting on a scrap piece first, and re-check the first holes of each batch.

    What is the difference between a countersink and a counterbore?icon-minus-redicon-plus-red

    A countersink cuts a cone-shaped recess that matches a countersunk (flat head) screw, so the head sits flush. A counterbore cuts a cylindrical recess with a flat bottom, which is what a socket head cap screw or a bolt head with a washer needs.

    Countersinks are also used to chamfer or deburr the edge of a drilled or tapped hole, which gives a lead-in for a tap or screw and removes sharp edges. If you only need to break an edge, a countersink is the usual tool; if the fastener has a flat-underside head that must be recessed, you need a counterbore.

    What safety precautions should I take with loose clothing, hair and gloves when countersinking?icon-minus-redicon-plus-red

    Countersinking uses rotating tools, so entanglement is a real risk. The HSE advises avoiding loose or baggy clothing, tying back or covering long hair, and avoiding jewellery, including rings, when operating engineering machinery. It also says many serious workshop accidents could be avoided if gloves were not worn near rotating machinery such as drills.

    Follow the machine maker's instructions and your own risk assessment. Hold or clamp the work securely so it cannot spin with the cutter, and keep hands clear of the rotating tool.

    Shop Similar Categories