The website is working fine. Please feel free to place orders. WE SHIP WORLDWIDE    /    All UK ORDERS GREATER THAN £75 EX VAT DELIVERED FREE    /    WE SHIP WORLDWIDE    /    ALL EUROPEAN ORDERS GREATER THAN £500.00 ex VAT DELIVERED FREE    /    WE SHIP WORLDWIDE
    Share this page on Facebook   Share this page on LinkedIn   Share this page on Twitter   Share this page on Whatsapp   

    Rapid Ref : H3116  Mfr Ref : 98-4BF

    Harris 98-4BF Three Hose 35 x 110mm Barrel Machine Cutting Torch.
    98-4BF H3116

    £335.68  EX VAT
    SSP Suggested Selling Price = £372.92  YOU SAVE £37.24
     Buy in 3 easy interest free payments of £111.89† with

    Harris machine cutting torches are designed to handle all types of machine cutting applications.

    General Features

    • Solid head for maximum strength
    • Standard 32mm or 35mm diameter barrel
    • 1/4 inlet threads 
    • Able to be used with 6290 machine cutting tips

    Torch Specifications

    • Same characteristics as 198-2T but valveless
    • Cutting capacity up to 380mm

    Harris Machine Torches FAQs

    Straight answers on choosing, setting up and looking after machine-mounted oxy-fuel cutting torches, with the safety points that matter most.

    What is a machine cutting torch and how does it differ from a hand torch?icon-minus-redicon-plus-red

    A machine cutting torch is a barrel-style torch that is clamped into a carriage, profile cutter, pipe-cutting rig or similar mechanised equipment instead of being held by an operator. The machine moves the torch at a steady speed along the line of cut, which is why it is used for long straight cuts, repeat shapes and bevels where an even, repeatable edge matters.

    The cutting process is the same as with a hand torch: a preheat flame brings the steel up to temperature and a jet of cutting oxygen burns through it. The differences are mostly in the build, such as a longer barrel to reach the work, a mounting point for the machine, and often a rack for height adjustment. Check the machine's mounting diameter before choosing.

    What do two-hose and three-hose machine torches mean?icon-minus-redicon-plus-red

    This usually describes how many gas hoses connect to the torch. A two-hose torch is normally fed with oxygen and fuel gas, and the preheat gases are mixed inside the torch before they reach the tip. A three-hose torch usually has separate connections for cutting oxygen, preheat oxygen and fuel gas, so the preheat oxygen and cutting oxygen can be set independently and the gases are often mixed at or near the nozzle.

    The exact arrangement varies with the design, so do not assume. The right choice depends on the fuel gas, the tips you plan to use and what your machine's gas controls can supply. Always follow the torch maker's instructions for hose connections, and check the tip type matches the torch type.

    Should I use acetylene or propane for machine cutting?icon-minus-redicon-plus-red

    Both work, and the choice depends on the job. Acetylene gives the hottest flame, so it starts a cut and pierces plate faster, and its focused flame suits thin plate and bevel cutting with little distortion. Propane has a lower flame temperature and is slower to pierce, but cutting speeds with comparable tips are similar, it often gives a smoother edge with less slag, and it tolerates more variation in nozzle height.

    The tip must be designed for the fuel gas you use, and the torch, hoses, regulators and arrestors must all be suitable for that gas. Ask your gas supplier or our team if you are unsure which suits your cutting thickness and equipment.

    Why is the top edge of my cut rounded or covered in slag?icon-minus-redicon-plus-red

    Common causes are too much preheat flame, a nozzle held too high, travel that is too fast or too slow, too much or too little cutting oxygen, and a dirty or damaged tip. Too much preheat tends to melt and round the top edge and adds slag. Travelling too fast leaves coarse drag lines and slag on the bottom edge. Too low a cutting oxygen flow gives poor slag removal.

    Work through the list one setting at a time: confirm the tip is clean and the right size for the thickness, set the nozzle height, reduce the preheat to the recommended setting, then adjust travel speed using the maker's chart. Make test cuts on offcuts before running a job.

    Shop Similar Categories