WE HAVE SOME GREAT LIMITED-TIME OFFERS - CLICK HERE TO VIEW THEM WE SHIP WORLDWIDE    /    All UK ORDERS GREATER THAN £75 EX VAT DELIVERED FREE    /    WE SHIP WORLDWIDE    /    ALL EUROPEAN ORDERS GREATER THAN £500.00 ex VAT DELIVERED FREE    /    WE SHIP WORLDWIDE

Flux Ovens

Flux Ovens FAQs

Answers to common questions about holding ovens and heated hoppers for submerged arc welding flux.

Why does submerged arc flux have to be kept dry?icon-minus-redicon-plus-red

Flux that has taken up moisture releases hydrogen into the weld pool when it melts in the arc. Moisture in the flux or electrode coating is the principal source of hydrogen in flux-based welding. Hydrogen in the weld can lead to delayed cracking, especially in higher-strength steels, and damp flux is also a known cause of porosity.

Keeping flux dry from the packet to the weld is therefore part of controlling weld quality. The flux maker's data sheet and your welding procedure set out how dry it needs to be for the job.

What is the difference between drying flux and holding flux in an oven?icon-minus-redicon-plus-red

Drying (sometimes called re-baking) removes moisture that flux has already picked up, and it uses a much higher temperature for a set time. Holding is the lower temperature used to keep dry flux dry until it is needed, which is what a holding oven or heated hopper is for.

Baking the flux before use may be necessary, and if flux is not used within a short time the hoppers on the equipment should be heated to limit moisture pick-up. Check the flux data sheet for the drying and holding temperatures, because they vary between flux types and makers.

Do all submerged arc fluxes absorb moisture in the same way?icon-minus-redicon-plus-red

No. Fused fluxes are made by melting and crushing, and are resistant to moisture pick-up. Agglomerated (bonded) fluxes are made from a baked wet mix with binders that attract moisture, so moisture pick-up can be a problem on the shop floor and baking before use may be needed.

This is why the type of flux affects how you store and handle it. Check the flux packaging and data sheet for the type and the maker's handling rules, and ask our team if you are unsure which oven arrangement suits your flux.

Do I need an oven if my flux comes in sealed packaging?icon-minus-redicon-plus-red

Not always. Some suppliers now pack flux in airtight packaging, which is designed to let it be used straight from the pack at low hydrogen levels without baking first. Once the pack is opened, though, the flux is exposed to the air and that protection stops.

If you use the whole pack quickly, an oven may not be needed. If opened flux sits in the hopper or is put back into storage, a holding oven or heated hopper is a sensible way to keep it dry. Follow the flux maker's instructions and your welding procedure for how long opened flux may be left.

Can compressed air used for flux recovery affect the flux?icon-minus-redicon-plus-red

Yes. Flux recovery units driven by compressed air can carry moisture and oil into the recovered flux if the air is not dry and clean. Compressed air used with a flux recovery unit should be thoroughly dried.

A damp or oily recirculating flux can cause porosity, even if it was dry in the oven. Drain the air line and filters regularly, and follow the recovery unit maker's instructions. Keep the recycled flux separate from any contaminated or wet flux.

Can I reuse recovered flux, and should it go back in the oven?icon-minus-redicon-plus-red

Recovered flux can often be reused, but it needs care. Recirculating flux can break it down into dust, and too many fines can trap gas under the slag and cause surface defects, so the system should filter out detached slag and fine dust.

Many flux makers also recommend topping up recycled flux with new flux in a set proportion. Recovered flux that has been exposed to the air should be held in the oven or a heated hopper like fresh flux. Follow the flux maker's instructions on proportions and how often it may be recycled.