WE HAVE SOME GREAT LIMITED-TIME OFFERS - CLICK HERE TO VIEW THEM WE SHIP WORLDWIDE    /    All UK ORDERS GREATER THAN £75 EX VAT DELIVERED FREE    /    WE SHIP WORLDWIDE    /    ALL EUROPEAN ORDERS GREATER THAN £500.00 ex VAT DELIVERED FREE    /    WE SHIP WORLDWIDE
  • GOV-200-FD  Gullco Flux Holding Oven 115 Volt, 100-550°F (38-288°C) Temperature, 1500 Watts. 88Kg Capacity
  • GOV-200-FD  Gullco Flux Holding Oven 115 Volt, 100-550°F (38-288°C) Temperature, 1500 Watts. 88Kg Capacity
Share this page on Facebook   Share this page on LinkedIn   Share this page on Twitter   Share this page on Whatsapp   

Rapid Ref : GOV-200-FD  

Gullco Flux Holding Oven 115 Volt, 100-550°F (38-288°C) Temperature, 1500 Watts. 88Kg Capacity
GOV-200-FD

£3050.00  EX VAT
 Buy in 3 easy interest free payments of £1016.67† with
Please note, this product does not qualify for our standard shipping rates outside of the UK Mainland. Please contact us for shipping rates for this product.

This insulated 88Kg capacity Flux Holding Oven is generally located in the storage area and is used to keep the flux in its dry state or to dry out flux that has picked up moisture. It is complete with lifting lugs, and hinged loading lid, a thermometer and a flux heating system incorporating 1500 watts of low-density elements. A thermostat controls the temperature. The temperature range is 100° to 550°F. All for operation on 115v. Weight 70Kg. Dimensions: 1372mm H x 508mm W x 610mm D.

Product Details

Brochures & Manuals

BROCHURES & MANUALS
   View Brochure

Flux Ovens FAQs

Answers to common questions about holding ovens and heated hoppers for submerged arc welding flux.

What is the difference between drying flux and holding flux in an oven?icon-minus-redicon-plus-red

Drying (sometimes called re-baking) removes moisture that flux has already picked up, and it uses a much higher temperature for a set time. Holding is the lower temperature used to keep dry flux dry until it is needed, which is what a holding oven or heated hopper is for.

Baking the flux before use may be necessary, and if flux is not used within a short time the hoppers on the equipment should be heated to limit moisture pick-up. Check the flux data sheet for the drying and holding temperatures, because they vary between flux types and makers.

Do all submerged arc fluxes absorb moisture in the same way?icon-minus-redicon-plus-red

No. Fused fluxes are made by melting and crushing, and are resistant to moisture pick-up. Agglomerated (bonded) fluxes are made from a baked wet mix with binders that attract moisture, so moisture pick-up can be a problem on the shop floor and baking before use may be needed.

This is why the type of flux affects how you store and handle it. Check the flux packaging and data sheet for the type and the maker's handling rules, and ask our team if you are unsure which oven arrangement suits your flux.

Can compressed air used for flux recovery affect the flux?icon-minus-redicon-plus-red

Yes. Flux recovery units driven by compressed air can carry moisture and oil into the recovered flux if the air is not dry and clean. Compressed air used with a flux recovery unit should be thoroughly dried.

A damp or oily recirculating flux can cause porosity, even if it was dry in the oven. Drain the air line and filters regularly, and follow the recovery unit maker's instructions. Keep the recycled flux separate from any contaminated or wet flux.

Can I reuse recovered flux, and should it go back in the oven?icon-minus-redicon-plus-red

Recovered flux can often be reused, but it needs care. Recirculating flux can break it down into dust, and too many fines can trap gas under the slag and cause surface defects, so the system should filter out detached slag and fine dust.

Many flux makers also recommend topping up recycled flux with new flux in a set proportion. Recovered flux that has been exposed to the air should be held in the oven or a heated hopper like fresh flux. Follow the flux maker's instructions on proportions and how often it may be recycled.

Shop Similar Categories