WE HAVE SOME GREAT LIMITED-TIME OFFERS - CLICK HERE TO VIEW THEM WE SHIP WORLDWIDE    /    All UK ORDERS GREATER THAN £75 EX VAT DELIVERED FREE    /    WE SHIP WORLDWIDE    /    ALL EUROPEAN ORDERS GREATER THAN £500.00 ex VAT DELIVERED FREE    /    WE SHIP WORLDWIDE

Orbitalum Sawblade Accessories

Suitable for all GF and RA machines, to increase the tool life of sawblades.

Orbitalum Sawblade Accessories FAQs

Straight answers on lubricants and other accessories that help orbital pipe-saw blades last longer and cut cleanly.

What does saw blade lubricant do on an orbital pipe saw?icon-minus-redicon-plus-red

A cutting lubricant reduces friction and heat at the teeth and helps carry away fine swarf, so the blade cuts more freely and usually lasts longer. Guidance for sawing stainless steel is to feed adequate cutting fluid to the cut rather than run dry, and the same logic applies to the small, fast-turning blades on an orbital saw.

Lubricants for this job are usually supplied as a paste or grease in a tube so that it can be applied to the blade teeth. How much benefit you see depends on the blade, the pipe material and the wall thickness, so always follow the blade maker's advice.

Why does stainless steel need extra care with lubrication when sawing?icon-minus-redicon-plus-red

Austenitic stainless steels (the common 300 series) tend to work harden. If the blade rubs or rides on the surface instead of cutting, the pipe wall can harden at that point and the teeth wear much faster. Trade guidance for sawing these grades is to start the cut cleanly, keep a positive feed and use a suitable cutting fluid.

On an orbital saw this means keeping the blade lubricated, not letting it dwell, and replacing a dull blade rather than forcing it. If you are unsure which lubricant suits your grade, ask the lubricant supplier or our team.

Do coated blades still need lubricant?icon-minus-redicon-plus-red

Often yes, although less is sometimes needed. Some hard-coated orbital saw blades are described by their makers as suited to minimum or spray lubrication and as giving good life even when cooling is not ideal. That does not mean they should be run completely dry.

Check the blade maker's instructions for the lubrication they expect with that blade and material. If the blade is not coated, or you are cutting a tough material such as stainless steel, a suitable lubricant on the teeth is normally the safer approach for tool life.

Do I need to clean lubricant off the pipe before welding?icon-minus-redicon-plus-red

Normally yes. Oil, grease and similar residues left on the cut end can contaminate the weld, so the pipe ends should be cleaned before welding. Stainless steel guidance recommends removing oil or grease with a suitable solvent such as acetone or alcohol, or with an alkaline cleaning solution.

Use clean cloths and gloves, let the surface dry fully and follow your welding procedure and the cleaner's safety data sheet. Orbital welding relies on well-prepared, clean ends that fit together closely, so it is worth cleaning every cut rather than assuming the end is clean enough.

Is it safe to apply lubricant to the blade while the saw is running?icon-minus-redicon-plus-red

No. Apply lubricant only when the machine is stopped, switched off and isolated from its power supply, and the blade has stopped moving. HSE guidance on work equipment says machines should be properly switched off, isolated or locked off before anyone cleans, adjusts or carries out maintenance on them, and that equipment should be used in line with the manufacturer's instructions.

Make sure the machine cannot be started accidentally while your hands are near the blade, and wear suitable gloves when handling sharp teeth. If your saw has a lubricant feature built in, follow the manual for how it should be used.

What precautions should I take with lubricant on my skin?icon-minus-redicon-plus-red

Treat cutting lubricants like other metalworking fluids. HSE guidance warns that metalworking oils can cause skin conditions such as dermatitis, particularly on the hands and arms, and that contamination in the fluid, such as fine metal particles, can add to the risk.

Avoid skin contact where you can, remove clothing that becomes soaked, and wash your hands after use with warm water and a mild cleanser. Barrier creams help but are not a full barrier. Read the safety data sheet for the specific lubricant, because the hazards depend on what is in it, and carry out a COSHH risk assessment.